rg131_radial_inserter_with_guide_pin_brochure.pdf

* It may not conform to Machinery Directive and EMC Directive in case of optional configuration and custom-made specification. Radial Lead Component Insertion Machine The RHSG has evolved. By supporting 3/4 pitches, expa…

100%1 / 2
* It may not conform to Machinery Directive and EMC Directive in
case of optional configuration and custom-made specification.
Radial Lead Component Insertion Machine
The RHSG has evolved.
By supporting 3/4 pitches, expanding the range of board sizes and increasing component
input, the high-density radial component insertion machines provide higher productivity.
* Values such as maximum speed may vary depending on operating conditions.
* Please refer to the ‘‘Specification’’ booklet for details.
*1: On condition
*2: Compatible with 3-phase 220 / 380 / 400 / 420 / 480 V
*3: Excluding signal tower
Model No.NM-EJR3A, NM-EJR4A
Model ID
Model ID
Model No.
PCB dimensions
Max. speed
*1
No.of component inputs
Applicable
components
Insertion direction
Electric source
*2
Pneumatic source
Dimensions
PCB exchange time
Mass
NM
-
EJR4A
L 50
mm
x W 50
mm
to L 508
mm
x W 381
mm
0.25 s/component to 0.6 s/component
80 (Connection mode), 40 + 40 (Exchange mode)
Pitch 2.5
mm
, 5.0
mm
, 7.5
mm
, 10.0
mm
Height Hn=Max. 26
mm
Diameter D=Max. 18
mm
Resistor, Electrolytic capacitor, Ceramic capacitor,
LED, Transistor, Filter, Resistor network
Pitch 2.5
mm
, 5.0
mm
, 7.5
mm
, 10.0
mm
Height Hn=Max. 26
mm
Diameter D=Max. 18
mm
Resistor, Electrolytic capacitor, Ceramic capacitor,
LED, Transistor, Filter, Resistor network
about 2 s to about 4 s (Room temperature 20℃)
4 directions (0 °, 90 °,
-
90 °,180 °)
3-phase AC 200 V, 3.5 kVA
0.5 MPa, 80 L/min (A.N.R.)
W 3 200
mm
x D 2 417
mm
x H 1 620
mm
*3
2 350 k
g
RG131
NM
-
EJR3A
L 50
mm
x W 50
mm
to L 508
mm
x W 381
mm
0.25 s/component to 0.6 s/component
40
about 2 s to about 4 s (Room temperature 20℃)
4 directions (0 °, 90 °,
-
90 °, 180 °)
3-phase AC 200 V, 3.5 kVA
0.5 MPa, 80 L/min (A.N.R.)
W 3 200
mm
x D 2 417
mm
x H 1 620
mm
*3
2 250 k
g
Model No.NM-EJR4A
RG131
Electronics Assembly System
catalog
2020
Higher insertion speed and operation efficiency improve productivity
Either one of 2-pitch (2.5mm/5.0mm), 3-pitch (2.5mm/5.0mm/7.5mm) or 4-pitch (2.5mm/5.0mm/7.5mm/10.0mm) spec. can be selected for insertion pitch.
Realized high speed insertion at a rate of between 0.25 s and 0.6 s per component. even for large-size components with
3-pitch (2.5mm/5.0mm/7.5mm) or 4-pitch (2.5mm/5.0mm/7.5mm/10.0mm) spec.
The use of guide pins makes high-density insertion possible when there is a gap between components.
Complete self-correction function ensures high reliability
Complete self-offset function covering the entire surface of the PC board ensures accurate insertion.
A total of up to 80 types of components can be mounted, with up to 32 (16 + 16) types of large-size components.
The two-separate component supply unit enable components to be exchanged and replenished during operation. (ex. exchange mode)
Reduction of running cost
Expendable parts of the RG131 such as the Anvil blade, lead cutter, chuck rubber and pusher rubber are compatible with those of the RHSG.
The transfer system, the XY table, the controller and the driver can be used in any one of the Insertion machine series.
The setup and maintenance operations are standardized.
Identical control panels are setup at the front side and the rear side of the RG131 so that operability can be significantly improved.
(Standard specification)
The liquid crystal touch panel is employed for the control panel and easy operation can be provided by the operation guidance indication.
Japanese, English or Chinese can be selected by one touch operation as the language used for the screen displays.
The new controller can store up to 200 types of programs. Data can be input to and output from high-capacity SD memory cards.
NC data of our conventional equipment (RH series) can be used by the RG131.
Setup support functions that display the component layout of the component supply unit on the screen are provided.
Maintenance support functions that display information of regular maintenance time and operation content are provided.
Maintenance support function
Rear side control panelSetup support function
Operation guidance indication
RG131
Model No.NM
-
EJR3A, NM
-
EJR4A
Model ID
Operability enhancement
With large numbers of component supply and dual-partitioned component supply units, long-term operation can be achieved.
Enlargement function option
Large-size PCB support option allows hole recognition and insertion up to PCB size of Max. 650 mm x 381 mm.
2 PCB transfer option can decrease PCB loading time by half and increase productivity.
This is effective especially when insertion components are few.
AR-DCE (model No. NM-EJS4B) Data Creation & Editor System
AR-DCE programming software can edit and optimize the program offline without affecting the machine operations.
3-1-1 Inazu-cho, Toyonaka City, Osaka 561- 0854, Japan
TEL +81-6-6866-8675
FAX +81-6-6862-0422
Inquiries…
Safety Cautions
●Please read the User's Manual carefully to
 familiarize yourself with safe and effective
 usage procedures.
● To ensure safety when using this equipment, all work should be
 performed according to that as stated in the supplied Operating
 Instructions. Read your operating instruction manual thoroughly.
Panasonic Group products are built with the environment in mind.
●Changes in specifications and appearance may be made without notice for product improvement.
●Homepage
Panasonic Corporation
Process Automation Business Division
Ver.January 1, 2020
All data as of January 1, 2020
©
Panasonic Corporation 2020
panasonic.com/global/corporate/sustainability
Please check the homepage for the details.
industrial.panasonic.com/ww/fa-jisso