QX600-8020146-REV_J.pdf

Q X600 ™ 2D A OI Contact C yberOptics today for mor e information +1 800.366.9131 or +1 763.542.5000 | CSsales@cyberoptics.com | www.cyberoptics.c om Copyright © 2012-2020. C yberOptics Corporation. All rights reserved. …

100%1 / 2
QX600™ 2D AOI
Contact CyberOptics today for more information
+1 800.366.9131 or +1 763.542.5000 | CSsales@cyberoptics.com | www.cyberoptics.com
Copyright © 2012-2020. CyberOptics Corporation. All rights reserved. Specications subject to change without notice. 8020146 Rev J
QX600
™
2D AOI
Ultra Fast, Ultra Versatile with Dual Lane and Large Board Capability
Best in
Class 01005 and
Solder Joint Inspection
2014 Global Technology Award
for QX600
Inspection Capabilities
Typical Scanning Speed 200 cm
2
/sec (31in.
2
/sec)
Minimum Component Size 0402 mm (01005 in.)
Board Length (without re-inspection) QX600: Min. 50 mm (2 in.)/ Max. 400 mm
†
(15.7 in.)
QX600-L: Min. 50 mm (2 in.)/ Max. 470 mm
††
(18.5 in.)
Board Width QX600: Min. 50 mm (2 in.)/ Max. 308 mm (12 in.)
QX600-L: Min. 50 mm (2 in.)/ Max. 510 mm (20.0 in.)
Board Length + Width
(QX600-D Model)
Single Lane: Boarder up to 520 (L) x 510 (W) mm (20.4 x 20.0 in.)
Dual Lane: Min. 50 mm (2 in.)/ 520 (L) x 300 (W) mm (20.4 x 11.8 in.)
Component Height Clearance (max)
(QX600 and QX600-L)
Top: 35mm (1.378 in.)
Bottom: 25mm (0.984 in.)
Component Height Clearance (max)
(QX600-D)
Top: 35mm (1.378 in.)
Bottom: 35mm (1.378 in.)
Board Edge Clearance (min) 3.0 mm (0.125 in.) – bottom side only
Component Types Inspected Standard SMT (chips, J-lead, gull-wing, BGA, etc.), through-hole, odd-form, clips, connectors, header
pins, and others
Component Defect Categories Missing, polarity, tombstone, billboard, ipped, wrong part, gross body and lead damage, and others
Solder Joint Defects Categories
Solder bridge, opens, lifted leads, wettability, excess and in sucient solder, debris, and others
Other Items Detected Gold-nger contamination, pin-in-hole, bent pins, debris, and many others
Component Position Categories Component X, Y position and Rotation
Measurement Gage R&R <10% (down to 0402 mm components)
† With re-inspection support, the board length can be extended to 550 mm (21.6 in.) using conveyor extension kit
† † Board length can be increased to 770 mm (30.3 in.) with integrated conveyor extension. With this set up, the line length will be 1700 mm (66.9 in.)
Vision System
Imagers 80 Megapixel sensor
Image Transfer Protocol PCIe
Lighting Strobe White Light (with dark/bright eld)
Resolution 12 μm pixel size
Image Processing Statistical Appearance Modeling (SAM™ ) Technology.
Option: Autonomous Image Interpretation (AI²) Technology
Programming Simple on-line or o-line, ePM software
CAD Import
Any column separated text le (Standard information required – ref. designator, XY, Angle, Part no.,)
System Specications
Conveyor Height Adjustable to 832 – 990 mm (33 – 39 in.)
Machine Interface SMEMA, RS232 and Ethernet
Alarms Light pole and audible alarm
Power Requirements 100-120V 60Hz or 220-240V 50Hz, 10 Amp max
System Dimensions (W x D x H) QX600 and QX600-D: 100 x 127 x 139 cm
QX600-L: 140 x 147 x 139 cm
Weight QX600: ~ 410 kgs (904 lbs.)
QX600-L: ~ 712 kgs (1570 lbs.)
QX600-D: ~ 605.2 kgs (1334 lbs.)
Machine Installation <1 hour
Options
SPC Software, Oine Defect Rework Station, Sensor Alignment Target, Barcode Readers (1D/2D), High Speed PC Kit, Dual Side Inspection Kit,
Right-to-left Conguration Kit
Inspect ‘Anything’
CyberOptics’ AI
2
(Autonomous Image Interpretation) technology
is designed for both low volume high mix, and high volume
low mix Applications, and builds on the proven success of our
Statistical Appearance Modeling technology. AI
2
is all about
keeping it simple - no parameters to adjust or algorithms to tune.
And, you don’t need to anticipate defects or pre-dene variance
either – AI
2
does it all for you.
QX600
™
Ultra Fast, Ultra Versatile
The QX600
TM
is powered by an all-new SIM (Strobed Inspection
Module) with enhanced illumination - designed to give you the
best 01005 and solder joint inspection performance ever. With a
higher sensor resolution (12 µm), you get to see crisp, perfect quality
images for more accurate defect review. And, as always, the SIM is
calibration-free. The QX600-D
TM
and QX600-L
TM
are also available for
dual lane and large board capabilities.
AI - Faster, Simpler, and Smarter
With AI
2
technology, programming gets even faster – with a 90%
reduction in examples required - so you get superior defect detection
and low false call rates even with just one example. This means
signicantly lower tuning time and quality results with one panel
inspection. Perfect for those high-mix or low volume applications!
With its unique ability to ‘ignore’ bad examples in a model, AI
2
oers
precise discrimination even with excessive variance and minimizes
eects of outlier examples. Plus, it is a lot simpler with full support for
unsupervised and semi-automatic model training. And, examples are
pre-sorted so you can select and clear the ones you don’t need – very
quickly. The pixel marking feature highlights defective spots, so you
can identify genuine defects instantly.
Just draw a box, show a few good examples and you are ready to
inspect just about anything. Simply add good examples to the AI
2
model and the false call rates reduce signicantly providing a very
robust inspection solution.
You can share components in the central model library and reuse
them when you create new programs - so much lesser programming
and so much more consistency
Fast, Scalable SPC Solution
CyberReport
TM
oers full-edged machine-level to
factory-level SPC capability with powerful historical
analysis and reporting tools delivering complete
traceability for process verication and yield
improvement. CyberReport
TM
is easy to setup and simple
to use while providing fast charting with a compact
database size.
Factory-level SPC
Line-level SPC
Machine-level SPC
Yield
Components Inspected/ Detected
SIM (Strobe Inspection Module)
Intelligent Ranking of Examples
Active Pixel Marking
3-Easy-Steps Programming
Our latest software improvements take programming
to a whole, new level – zero to production ready in less
than 13 minutes! All this is made possible, with an
all-new data-rich, pre-loaded library and automated
scripts that collect examples and update models – all
on their own.
01005 component size inspection
capaility
CYBERREPORT
SPISOFTWARE
AOISOFTWARE
CYBERREPORT
CYBERCMM
SPISOFTWARE
AOISOFTWARE
CYBERCMM
CYBER
PRINTOPTIMIZER
CYBER
PRINTOPTIMIZER
CYBERREPORT
SPISOFTWARE
AOISOFTWARE
CYBERREPORT
CYBERCMM
SPISOFTWARE
AOISOFTWARE
CYBERCMM
CYBER
PRINTOPTIMIZER
CYBER
PRINTOPTIMIZER
QX600-D
Dual Lane Dual Sensor
QX600-L
Large Board Capability
Flexibility At Its Best
The QX600-D™ dual lane - dual sensor system maximizes exibility catering to varying PCB widths. This
unique design provides the ability to inspect high volume assemblies, the convenience of inspecting dierent
assemblies and board sizes simultaneously on dierent lanes, or even switching from dual lane to single
lane mode to inspect very large boards. The QX600-L™ expands the standard QX600™ to support large board
inspection of up to 590 x 510mm sizes.