TK25947.Auto Create Parts Recognition Data.pdf

 SMT Software Engineering Group  IM Operations Y AMAHA MOTOR CO., L TD   MDOC-SOFT50408  1/8  Auto Create Parts Recognition Da t a Conte n t s Auto Create Parts Recognition Data  ....... .......... ....... ......…

100%1 / 8
SMT Software Engineering Group
IM Operations YAMAHA MOTOR CO., LTD
MDOC-SOFT50408
1/8
Auto Create Parts Recognition Data
Contents
Auto Create Parts Recognition Data....................................................................................................................1
Contents..............................................................................................................................................................................1
1. Model and Version....................................................................................................................................................2
2. Introduction...................................................................................................................................................................2
3. Procedure of parts recognition data auto creation...................................................................................4
3.1 Auto creation of alignment type and measurement data..............................................................4
3.2 Auto creation of Body Size without changing Alignment Type...................................................5
4. Function Details.........................................................................................................................................................6
4.1 Auto-created parameter.................................................................................................................................6
4.2 Alignment Type automatically created....................................................................................................7
Rev Version Chapter Revised Contents
00 V3.46STD R1.000 or later
V4.50STD R1.000 or later
All Created
本文書に含まれる技術内容は当社の秘密情報です。当社の許諾無く第三者への開示はできません。
The information contained in this message may be confidential and legally protected under
applicable law. The message is intended solely for the addressee(s).
If you are not the intended recipient, you are hereby notified that any use, forwarding,
dissemination, or reproduction of this message is strictly prohibited and maybe unlawful.
SMT Software Engineering Group
IM Operations YAMAHA MOTOR CO., LTD
MDOC-SOFT50408
2/8
1. Model and Version
Supported models and version are as follows.
Table1 Model and Version
Model･Software Version Remarks
YS series mounter V3.46STD R1.000 or later
YSM40, YSM20 V4.50STD R1.000 or later
2. Introduction
This function can automatically create parts data and recognition data based on parts
images. It is possible to create accurate parts data in a short time regardless of operator’s
skill.
The [Parts Find Best Target] combo box has been added on the [Parts Adjust] screen.
When you select a target and click the [Find Best] button, each parameter of the selected
parts is automatically created.
Also, “Defined Shape” is added to the [Monitor Mode] combo box. In this mode, parts
recognition image and a defined shape are overlaid on the view window.
In addition, [Alignment Group], [Alignment Type], [Algorithm], [Body Size X], and [Body
Size Y] are displayed on the grids of parts data, which makes it easy for you to confirm
and edit the setting values.
< Remarks >
This function has the following limitations.
1. In any of the following conditions, [Alignment Type] and [Body Size] are NOT created
by the [Find Best] button.
When the [Find Best] button is pressed on the [Parts Adjust] screen that opens at
pick up error or recognition error during auto-running.
When the [Find Best] button is pressed on the [Random Ball Edit] screen or the
[Pin Position Edit screen] screen.
When parts recognized by a single camera is selected and the [Find Best] button
is pressed.
2. Parts data of random ball parts is NOT automatically created.
3. Recognition data of [Datum Angle] set to “Normal” is created assuming [defined angle]
SMT Software Engineering Group
IM Operations YAMAHA MOTOR CO., LTD
MDOC-SOFT50408
3/8
as “0” according to the parts image.
4. Parts size (X, Y, ReflectLL, Lead Width) may differ from the actual size because it is
measured based on the electrode position and lighting condition.
5. When large parts need divided recognition, parts data is NOT automatically created.
6. If auto creation is executed while no parts are picked on head, there is a possibility that
data to recognize nozzle shape may be created.
7. On a machine equipped with both scan camera and multi-camera, recognition is
always performed by multi-camera.
Fig.1 Parts Adjust screen
Table2 “Parts Find Best Target” combo box
Item name Operation at Parts Find Best
Light Parameters of Lighting Level and Comp. Threshold are
automatically adjusted.
Size, Light Body Size is automatically created without any change of
“Alignment Type”. Also, “Find Best” of the light level is executed.
Type, Size, Light “Alignment Type” and “Body Size” are automatically created.
Also, Find Best of the light level is executed.