PSE_300_VS_TI_EN.pdf
Page 1 of 4 11/2021 The kolb PSE economy line is a quality series of advanced cleaning systems, which focuses on all essential criteria for a qua- lified cleaning process and therefore stands for attractive purchase pric…
Page 1 of 4
11/2021
The kolb PSE economy line is a quality series of advanced cleaning systems, which focuses on all essential criteria for a qua-
lified cleaning process and therefore stands for attractive purchase prices.
kolb PSE 300 VS is an extremely compact first-rate performance PowerSpray
®
system designed and manufactured in
Germany for smaller quantities with very short cycle times due to an intelligent 2step process with patented high performance
supercharger drying.
PS 300E VS delivers best possible cleaning of screens, stencils, misprints and solder frames, today a prerequisite for reprodu-
cible quality in production, the reduction of expensive production stand-stills and as well for high customer satisfaction.
The cleaning system can be operated with all common electronics cleaning supplies (detergents / chemistry, etc.)
which are approved by the manufacturer.
Mono-tank compact system with two tank function
Waterless / independent, no water / waste water connection necessary
Comfortable push one button operation
Fully automatic 2step process: cleaning / rinsing, drying with CWA
®
-supercharger compression drying
Vertical rotor system with two asynchronous spray rotors for thorough wetting (no blind spots)
Process and service intervals PLC controlled, event issuing and software control via 3,5" touch screen
Process sections made of electrolysis and high temperature resistant elements
Safe installation close to the production line possible; no special protection required
Certified for solar cell production
Extremely compact - maximum capacity on a very small footprint
Cleans Screens, stencils, solder carriers, misprints from SMD
paste, flux, oil, dust, grease
Capacity: Screen, stencil, carrier, washing frame up of 950 x
780 mm (37.5 "x 31")
Part number: 0905PSE3VS-2
Fully automatic single chamber PowerSpray
®
-system with
2step process (cleaning / rinsing, drying)
Solder carriersMisprintsStencilsScreens
PSE 300 VS
Compliant
WEEE
ClosedLoop
PowerSpray
®
Made in Germany
CLEANING TECHNOLOGY
kolb Cleaning Technology GmbH ▪ Karl-Arnold-Str.12 ▪ D - 47877 Willich ▪ Phone: +49 (0) 2154 9479 - 38 ▪ Fax: +49 (0) 2154 9479 - 47 ▪ e-mail: info@kolb-ct.com ▪ www.kolb-ct.com
Key applications
Certifications:
This water free operating system was certified in its basic version
for its energy saving processing, for easy operability and for the stan-
dard integration of comprehensive safety features.
All rights for changes reserved that lead to technical improvement. © kolb GmbH 2021
Most suitable Optional suitable Not suitable Not suitableNot suitable
Cleaning / rinsing (key process 1): From the system tank a communicating cleaning and rinsing liquid is sucked by a
magnetically coupled pump unit and routed with a controllable volume flow into the ASYNCHRO
®
spray rotors with patented
PUSHFORCE
®
nozzles. Their geometry ensures a comprehensive and thorough cleaning, even in inaccessible and critical
aereas. The liquid is continuously filtered in circulation, so that the system progressively enters the rinsing process after
removing the contamination.
Drying (key process 2): The purified products are dried with the patented CWA
®
(Compressed Warm Air) technology. The
built-in special compressor compresses the ambient air. At the same time it collects the kinetic energy (frictional heat) of the
paddle wheel in the unit, then presses the heated and compressed air into the rotor nozzles which were already used for clea-
ning and rinsing. There it blows off (pressure) and evaporates (heat) the residual moisture. This method is energetically and
constructively highly efficient, as it uses the "waste heat" of the compressor rotation and the compressed air as driving power
for the rotors. In addition, a system equipped with CWA
®
technology requires no additional hardware and no external com-
pressed air connection for the MediumWipe
®
process.
Cycle time: < 18 min., depending on contamination and detergent
Maintenance: The system has a removable panel on the right side. In the maintenance area among others the pump-out set
is available. Tank levels as well as pressure values and maintenance cycles are monitored by the PLC. The tank level is also
easily controllable through a window in the system front.
Page 2 of 4
Part number: 0905PSE3VS-2
Fully automatic single chamber PowerSpray
®
-system with
2step process (cleaning / rinsing, drying)
11/2021
PSE 300 VS
Made in Germany
CLEANING TECHNOLOGY
kolb Cleaning Technology GmbH ▪ Karl-Arnold-Str.12 ▪ D - 47877 Willich ▪ Phone: +49 (0) 2154 9479 - 38 ▪ Fax: +49 (0) 2154 9479 - 47 ▪ e-mail: info@kolb-ct.com ▪ www.kolb-ct.com
Application overview
Solder frames
Solder carriers
Solder masks
ESD Boxes
Containers
Magazines
Condensation traps
Filters
Steel sheets
Optional suitable applications can also be optimally realized with the appropriate options.
Stencils
Screens, PumpPrints
Misprints (bare boards)
Assembled PCBs
Hybrids
Misprints (mounted)
All rights for changes reserved that lead to technical improvement. © kolb GmbH 2021
Main standard features
□ PowerSpray
®
technology bundle: magnetically coupled S-Power pump unit, twofold ASYNCHRO
®
volume-spray rotorsysterm
with PUSHFORCE
®
nozzles
□ Magnetic coupled pump unit
□ EATON Programmable Logic Controller (PLC)
□ High resolution 3.5" touch display
□ Full flow coarse filter (process chamber)
□ CWA
®
-supercharger compression drying
□ ClosedLoop reprocessing of cleaning and rinsing fluid
□ Safety features: safety interlock on the process chamber door, overheating protection for all heating and drying elements,
end switches for all motor-driven valves and drives, personnel protection insulation
□ Front cover made of stainless steel, side and rear covers in painted steel
□ Process sections made of electrolysis resistant elements
Main options
□ Cascaded filter system / Sediment filter for cleaning / rinsing tank
□ Drip & storage reservoir
□ Exhaust controil
□ Full stainless steel housing
□ Noise insulation
Page 3 of 4
Part number: 0905PSE3VS-2
Fully automatic single chamber PowerSpray
®
-system with
2step process (cleaning / rinsing, drying)
11/2021
PSE 300 VS
Made in Germany
CLEANING TECHNOLOGY
kolb Cleaning Technology GmbH ▪ Karl-Arnold-Str.12 ▪ D - 47877 Willich ▪ Phone: +49 (0) 2154 9479 - 38 ▪ Fax: +49 (0) 2154 9479 - 47 ▪ e-mail: info@kolb-ct.com ▪ www.kolb-ct.com
All rights for changes reserved that lead to technical improvement. © kolb GmbH 2021