N5227B.pdf - 第73页

Find us at www. keysi ght.com Page 73 Description Typical Perfo rmance 0.1 dB Compres sion Point Normal IF path Narrowband I F path - 9.0 dBm at 7. 438 MHz - 17 dBm at 10.70 M Hz Pulse I/O Connec tor 15 - pin mini D - su…

100%1 / 90
Find us at www.keysight.com Page 72
Description Typical Performance
Display Range
Magnitude
±2500 dB (at 500 dB/div), max
Phase
±2500° (at 500 degrees/div), max
Polar
10 pUnits, min
10,000 Units, max
Display Resolution
Magnitude
0.001 dB/div, min
Phase
0.01°/div, min
Marker Resolution
Magnitude
0.001 dB, min
Phase
0.01°, min
Polar
10 pUnit, min
Table 75. Rear Panel Information, All Options
Description Typical Performance
10 MHz Reference In
Connector
BNC, female
Input Frequency
10 MHz ±1 ppm, 100 MHz ±1 ppm
20 MHz ±1 ppm, 80 MHz ±1 ppm
Input Level
10 MHz: -15 dBm to +20 dBm
100 MHz: -10 dBm to +20 dBm
Input Impedance
50 Ω, nom.
10 MHz Reference Out
Connector
BNC, female
Output Frequency
10 MHz ±0.7 ppm, 100 MHz ±0.7 ppm
Signal Type
Sine Wave
Output Level
+10 dBm ±4 dB into 50 Ω
Output Impedance
50 Ω, nominal
Harmonics
<-40 dBc, typical
External IF Inputs
Function
Allows use of external IF signals from remote mixers, bypassing the PNA's first converters
Connectors
SMA (female); A, B, C, D, R (4-port); A, B, R1, R2 (2-port)
Input Frequency
Normal IF path
Narrowband IF path
RF < 53 MHz: IF = 826.446 KHz
RF >= 53 MHz: IF = 7.438 MHz
IF = 10.70 MHz
Input Impedance
50 Ω
RF Damage Level
+23 dBm
DC Damage Level
5.5 VDC
Find us at www.keysight.com Page 73
Description Typical Performance
0.1 dB Compression Point
Normal IF path
Narrowband IF path
-9.0 dBm at 7.438 MHz
-17 dBm at 10.70 MHz
Pulse I/O Connector
15-pin mini D-sub (for pin assignment information, refer to the PNA online help)
Pulse Inputs (IF Gates)
Function
Internal receiver gates used for point-in-pulse and pulse-profile measurements
Input Impedance
1 K Ohm
Minimum Pulse Width, Source Modulators
33 ns
Minimum Pulse Width, Receiver Gates
20 ns
DC Damage Level
5.5 VDC
Drive Voltage
0 V (off), +3.3 V (on), nominal
RF Pulse Modulator Input (Source Modulator)
On/Off Ratio
10 MHz to 3.2 GHz
-64 dB
3.2 GHz to 67 GHz
-80 dB
Pulse Period
Minimum
33 ns
Maximum
70 s
Pulse Outputs
Voltage (TTL)
High: 3.3V to 3.5V
Low: <1V
Impedance
50 Ohm
External Test Set Driver
Function
Used for driving remote mixers
Connections
3.5 mm (female)
RF Output Frequency Range
3.2 GHz to 19 GHz
LO Output Frequency Range
0.01 GHz to 26.5 GHz
Rear Panel LO Power
Upper Limit, Typical (dBm)
Lower Limit, Typical (dBm)
10 MHz to 1.7 GHz
--
--
1.7 GHz to 16 GHz
5
-3
16 GHz to 21 GHz
0
-6
21 GHz to 26.5 GHz
4
-5
Rear Panel RF1 / RF2 Power
Maximum Output Power, Typical (dBm)
3.2 GHz to 5 GHz
+3
5 GHz to 19 GHz
+8
Bias Tee Inputs
Connectors
BNC(f) for ports 1, 2, 3 and 4
Fuse
500 mA, bi-pin style
Find us at www.keysight.com Page 74
Description Typical Performance
Maximum Bias Current
±200 mA with no degradation of RF specifications
Maximum Bias Voltage
±40 VDC
Other Rear Panel Interface
Trigger Inputs/Outputs
BNC(f), TTL/CMOS compatible
Test Set IO
25-pin D-Sub connector, available for external test set control
Power IO
9-pin D-Sub, female; analog and digital IO
Handler IO
36-pin parallel I/O port; all input/output signals are default set to negative logic; can be reset to
positive logic via GPIB command
GPIB
Two ports - dedicated controller and dedicated talker/listener. 24-pin D-sub (Type D-24),
female; compatible with IEEE-488
CPU Version
CPU version 7.0, 8.0
CPU version 9.0
PCIe
Cabled PCIe x4 connector is a 4-lane slot
N/A
USB Ports
Two SuperSpeed USB ports (900 mA each),
one USB port below LAN connector, and one
USB device port. There are also four USB
ports (500 mA each) on the front panel. The
total current limit for all rear panel USB ports
is 2.3 amps. The total current limit for all front
panel USB ports is 2 amps.
Four SuperSpeed USB ports (900 mA each)
and one USB device port. There are also four
USB ports (500 mA each) on the front panel.
The total current limit for all rear panel USB
ports is 3.6 amps. The total current limit for all
front panel USB ports is 2 amps.
USB-C (Host)
N/A
Two USB-C connectors with support for USB-
3.1 (max Power Delivery of 5V@1A),
Thunderbolt3 (max Power Delivery of
5V@1A)
1
, and Display Port (port TB1 only)
LAN
1G port;
10/100/1000 BaseT Ethernet, 8-pin
configuration; auto selects between the data
rates
1G and 10G ports;
10GBASE-T, Ethernet, 8-pin configuration;
auto selects between the data rates. Works
with Cat6/Cat7 cable.
VGA Video Output
15-pin mini D-Sub; Drives VGA compatible
monitors
N/A
Mini DisplayPort
Miniature DisplayPort connector for
connection to external displays
N/A
DisplayPort
N/A
Standard DisplayPort connector for
connection to external displays
Line Power
Frequency, Voltage
50/60/400 Hz for 100/120 VAC
50/60 Hz for 220/240 VAC
Power supply is auto switching
Max
575 watts
1
High power devices require external power supply.