00198271-02_UM_ShuttleExtensionTX_EN - 第49页
Assembly and User Manual 3 Assembly Instruction Shuttle Extension Edition 06/2017 3.4 Electrical Connections 47 3.4.2 SIPLACE TX Connection 3.4.2.1 Overview Fig. 3.4 - 2 SIPLACE TX Connection (1) SMEMA connection T1 U PS…
3 Assembly Instruction Assembly and User Manual
3.4 Electrical Connections Shuttle Extension Edition 06/2017
46
3.4 Electrical Connections
3
3.4.1 Shuttle Extension
Connect the following cables to the Shuttle Extension connection.
– 4 x SMEMA Cable [Item. No.: 03152800-xx]
– 1 x CAN Bus cable [Item. No.: 03133551-xx]
– 1 x Power interface cable to SIPLACE TX [Item. No. 03133550-xx]
Fig. 3.4 - 1 Electrical connection on the Shuttle Extension
(1) SMEMA connection XL1 UPSTREAM - Lane 1 to predecessor machine
(2) SMEMA connection XL2 UPSTREAM - Lane 2 to predecessor machine
(3) CAN-BUS connection
(4) SMEMA connection XL2 DOWMSTREAM - Lane 2 to successor machine
(5) SMEMA connection XL1 DOWMSTREAM - Lane 1 to successor machine
(6) POWER interface X50 to SIPLACE TX
PLEASE NOTE
Use of the circuit diagrams of the Shuttle Extension
For detail information, please refer to the circuit diagrams of the Shuttle Extension.
(6)
(1)
(2)
(3)
(4)
(5)
Assembly and User Manual 3 Assembly Instruction
Shuttle Extension Edition 06/2017 3.4 Electrical Connections
47
3.4.2 SIPLACE TX Connection
3.4.2.1 Overview
Fig. 3.4 - 2 SIPLACE TX Connection
(1) SMEMA connection T1 UPSTREAM
(2) SMEMA connection T1 DOWNSTREAM
(3) SMEMA connection T2 UPSTREAM
(4) SMEMA connection T2 DOWNSTREAM
(5) CAN-BUS Connection (for termination and connection see section 3.4.2.2
, page 48 and
3.4.2.3
, page 49)
(6) Power interface to the output Shuttle Extension
(7) Power interface to the input Shuttle Extension
(7)
(6)
(5)
(1)
(2)
(3)
(4)
3 Assembly Instruction Assembly and User Manual
3.4 Electrical Connections Shuttle Extension Edition 06/2017
48
3.4.2.2 Connections
The Shuttle Extension has two configurations, namely the upstream and downstream, wiring con
-
nections and jumpers setting are stated below.
3
For special configurations where two Shuttle Extensions are link to a single SIPLACE TX ma
-
chine, the CAN cable and TSP 420 jumper setting will be configure as per below.
3
Upstream configurations Downstream configurations
Power connection to TX -X15.S1 -X15.S2
CAN Bus connection to TX CAN3.EXT CAN3.EXT
Power connection to TX X50 X50
CAN Bus connection to Shuttle X52 X52
SMEMA connection to TX -XL1 and XL2 upstream -XL1 and XL2 downstream
SMEMA connection to Shuttle -XL1-DS and XL2-DS (Down
-
stream)
-XL1-US and XL2-US
(Upstream)
TSP 420 jumper setting JP1 pin 2 and 3 is shorted
JP2 pin 1 and 2 is shorted
JP1 pin 2 and 3 is shorted
JP2 pin 1 and 2 is shorted
CAN termination connector re
-
moved from CAN3.EXT
Plugged into -X1* (CAN ca
-
ble: upstream)
Plugged into -X1* (CAN ca
-
ble: downstream)
CAN cable IDC Connector Upstream configurations Downstream
configurations
-X1 -X1*(cable: downstream) CAN3.EXT (TX)
-X1* CAN termination connector
removed from CAN3.EXT
-X1 (cable: upstream)
-X52 -X52 (shuttle upstream) -X52 (shuttle downstream)
TSP 420 jumper setting
JP1 pin 2 and 3 is shorted
JP2 pin 1 and 2 is shorted
JP1 pin 2 and 3 is shorted
JP2 pin 1 and 2 is shorted