HS50_advance_level 2 - 第109页
Stud ent Gu ide HS-5 0 Adva nced II 07/2 002 Ed ition 4 Pneum atic 7 The air i s suppli ed to t he colle ct & p lace head in se vera l pipes, each o f whic h is sup plied wit h a 5.3 bar p ressure. All p ipes a re la…
07/2002 Edition Student Guide HS-50 Advanced II
4 Pneumatic
6
9DFXXPV\VWHPRQWKH&3+HDG
Bulk Case Supply
Gantry 1
Gantry 2
Gantry 4
Gantry 3
B5.1
B5.4
B5.3
B5.2
B4
B7
B6B2
Stopper / Cutter
B8
Nozzlechanger 2/3
B12.1
Nozzlechanger 1/4
Feeder Table 2/3
Feeder Table 1/4
B12.2
B13.1
B13.2
not used
not used
B10
B11
6,5 - 8 bar
main valve
filter
5,3 bar
2,3 bar
Student Guide HS-50 Advanced II 07/2002 Edition
4 Pneumatic
7
The air is supplied to the collect & place head in several pipes, each of which is supplied with a
5.3 bar pressure. All pipes are labelled and should be attached to the head as shown in the dia-
gram above.
The air supply at the collect & place head is used for two principle things, vacuum generation and
air kiss.
9DFXXP6\VWHP
The air is supplied to the venturi block, which produces a vacuum using the venturi principle. The
venturi block actually consists of 2 separate venturi which produce vacuum for 2 circuits, the hold-
ing circuit and the pick up / placement circuit.
EOLQG
33
quadruplicate distributor
below head board
4
4
E2
E1
6,5 - 8 bar
E3
B5.1 or
B5.2 or
B5.3 or
B5.4
A1
A4
A6
A2
A5
A3
A7
Adjustable
valve
Adjustable
valve
Valve plunger
Holding
circuit
Valve plunger
Valve plunger
Vacuum
sensor
To vacuum board
Reject
circuit
Vacuum
sensor
To vacuum board
Forced air
sensor
to adapter board
Pickup /
placement circuit
forced air
0.2 - 0.3 bar
forced air
0.15 - 0.2 bar
07/2002 Edition Student Guide HS-50 Advanced II
4 Pneumatic
8
The level of vacuum produced is dependant on a number a factors the most obvious of which is
the condition of the venturi itself. Any leakage from or blockage within the system will result in it
working inefficiently and therefore a reduction in the vacuum levels created. Therefore it is impor-
tant that the venturi is correctly sealed when reassembled and that the condition of the nozzles
within the system is good.
There are other factors that will affect the vacuum levels generated that are beyond your control
however. The most significant of these is altitude. The higher above sea level a machine is located
the lower the ambient pressure in the room surrounding it is. Therefore at high altitude low vacuum
levels are created, an example is a machine in Munich, Germany at an altitude of 500m may gen-
erate closed vacuum results of 870 mB whereas the same machine at almost sea level in the UK
would generate vacuum results of 920mB.
The other factor that can result in lower vacuum results is the weather. On a stormy rainy day a
Low pressure system will be present and may result in closed vacuum results of 880 mB. A week
later a bright sunny day results due to a High-pressure system. In this case closed vacuum results
of 900 mB may result.
These 2 cases are only examples and no specific case / figures are used, but this just illustrates
what can happen. In these cases it becomes even more important that the venturi system is well
maintained and therefore performing efficiently.
9DFXXP3UHVVXUH0HDVXUHPHQW3&%
A small PCB mounted on the venturi block measures the vacuum pressure within the holding and
pick up / placement circuits. Small tubes are attached to the back of the collect & place head that
mea-sure the circuit pressures at the vacuum distributor. These tubes are connected to pressure
sen-sors. The analogue outputs of these sensors are supplied to A/D converters. The resulting
signals are then sent via the CANBUS to the machine controller.