ASM_MANUAL_TYPHOON_USC_en_100620_online.PDFA - 第12页
3 TYPHOON UNDER STENCIL CLEANER 3.2 USC ASSEMBLIES 12 STANDALONE MANUAL TYPHOON UNDER STENCIL CLEANER 06/2020 3.2 USC ASSEMBLIES NOTE The information and illustrations throughout the rest of this manual detail the standa…
3 TYPHOON UNDER STENCIL CLEANER
3.1 OVERVIEW
STANDALONE MANUAL TYPHOON UNDER STENCIL CLEANER 06/2020 11
8
13
11
12
9
10
1
2
21
20
19
17
18
16
15
14
7
5
4
6
3
Long Board (620mm) Typhoon USC
1 Power and Control Loom
Connector (loom not shown)
12 Left-Hand Home
Electromagnetic Clamp
2 Right-Hand Y Linear Rail
Attachment
13 USC Home Sensor
3 Right-Hand Home
Electromagnetic Clamp
14 Left-Hand Y Linear Rail
Attachment
4 Fabric Roll Brake 15 Left-Hand Camera Beam
Attachment Electromagnetic
Clamp
5 Fabric Usage Sensor 16 Fabric Take-Up Roller
6 Fabric Usage Roller 17 Vac Chamber
(with Poly Blade Insert fitted)
7 Solvent Spray Bar 18 Right-Hand Vac Chamber Lift
Actuator
8 Fabric Roll Fitted (not spooled) 19 Fabric Roll Motor
9 Vac Arm 20 Right-Hand Camera Beam
Attachment Electromagnetic
Clamp and USC Detached
Sensor
10 Vac Chamber Vac Inlet 21 Solvent Pump
11 Left-Hand Vac Chamber Lift
Actuator
3 TYPHOON UNDER STENCIL CLEANER
3.2 USC ASSEMBLIES
12 STANDALONE MANUAL TYPHOON UNDER STENCIL CLEANER 06/2020
3.2 USC ASSEMBLIES
NOTE
The information and illustrations throughout the rest of this manual detail the standard version of
the Typhoon USC (300, 400, 460 and 515mm widths) but also apply to the Long Board (620mm)
version. The Long Board (620mm) version is only shown/mentioned where there is a recognisable
difference.
3.2.1 USC Base Unit
The base unit supports the other USC assemblies and attaches the USC to linear bearings (one
per end) which allow the USC to run along linear rails, when pulled by the camera carriage during
cleaning sweeps.
The right-hand end bracket connects to a drag-chain, which supplies all power and control looms,
pneumatics and solvent to the USC. This bracket also houses the earth stud.
Two home position electromagnets are fitted to the end of the linear rails, these become energized
to hold the USC in the home position. The left-hand end electromagnet has a through beam opto
sensor, which signals to the printer that the USC is in the home position when the associated vane
is detected.
Two camera carriage attachment electromagnets are fitted to the rear of the USC base unit. The
electromagnets attach the USC to the camera carriage, so it can be moved during cleaning
sweeps. The right-hand electromagnet has a through beam opto sensor, when the USC is attached
to the camera carriage the associated plunger/vane is pushed towards the sensor signaling to the
printer that the USC is attached. If, for any reason, the USC is not connected to the camera car-
riage when it should be, the lack of plunger/vane through the sensor signals to the printer that the
USC has been "detached".
3 TYPHOON UNDER STENCIL CLEANER
3.2 USC ASSEMBLIES
STANDALONE MANUAL TYPHOON UNDER STENCIL CLEANER 06/2020 13
1
2
3
4
9
10
11
16
5
6
7
8
12
13
14
15
1 Power and Control Loom
Connector
9 Left-Hand End Linear Bearing
2 Earth Stud 10 Left Linear Rail
3 Right-Hand Home
Electromagnetic Clamp
11 Left-Hand Camera Beam
Attachment Electromagnetic
Clamp
4 Right-Hand End Linear Bearing 12 USC Detached Sensor
5 Left-Hand Home Electromagnetic
Clamp
13 USC Detached Sensor Plunger/
Vane
6 USC Home Sensor 14 Right-Hand Camera Beam
Attachment Electromagnetic
Clamp
7 USC Vane 15 Camera Beam Magnetic Plate
8 USC Vane (Home Position) 16 Right Linear Rail