ASM_MANUAL_TYPHOON_USC_en_100620_online.PDFA - 第24页

3 TYPHOON UNDER STENCIL CLEANER 3.5 PNEUMATIC SCHEMATIC 24 STANDALONE MANUAL TYPHOON UNDER STENCIL CLEANER 06/2020 3.5 PNEUMATIC SCHEMATIC The pneumatic supplies for the USC lift actuators and fabric roll clamp are suppl…

100%1 / 62
3 TYPHOON UNDER STENCIL CLEANER
3.4 ELECTRICAL SCHEMATIC
STANDALONE MANUAL TYPHOON UNDER STENCIL CLEANER 06/2020 23
Part M37 Power Supply
M37PL35
L
N
E
Part
I/O Node 4
Part M36
Control Enclosure
M36PL9 9SK69 9PL69
Service Panel
AN IN0+
AN IN0-
0V USR
+12V
-12V
9SK/9PL63
Optional
Solvent Level
Amplifier
9SK/9PL64
Solvent Tank Weigh
Single Point Load Cell
9SE26
Solvent ‘Time To Go’ Option
E By DEK Variation
Solvent Float
Sensor
9SE69
9PL69 9SK/9PL130
Output
0V
+V
Vacuum Filtration
Unit
N4PL6
Venturi Vacuum
Solenoid
8SOL29
8SK60
N4PL6
Venturi Vacuum Filtration Option
M35SK1
N4PL10
P P
Low Pressure
Switch
High Pressure
Switch
DIG IN 6
0V Return
DIG IN 7
0V Return
M35SK/M35PL3
USC Vacuum Sensing Option
M35SK2
Typhoon Schematic - Sheet 3 of 3
3 TYPHOON UNDER STENCIL CLEANER
3.5 PNEUMATIC SCHEMATIC
24 STANDALONE MANUAL TYPHOON UNDER STENCIL CLEANER 06/2020
3.5 PNEUMATIC SCHEMATIC
The pneumatic supplies for the USC lift actuators and fabric roll clamp are supplied via two solen-
oid valves fitted to the printer's rear pneumatic manifold (illustrated below).
A AB B
O
S
16SOL08
PLENUM LIFT
FABRIC ROLL BRAKE
16SOL06
3 TYPHOON UNDER STENCIL CLEANER
3.6 REPLENISHMENT PROCEDURES
STANDALONE MANUAL TYPHOON UNDER STENCIL CLEANER 06/2020 25
3.6 REPLENISHMENT PROCEDURES
3.6.1 Fabric Roll
Fabric rolls for the Typhoon USC are available in 300mm, 400mm, 515mm (used for 460mm and
515mm) and 620mm widths to suit a variety of board lengths. To replace a used fabric roll, or to
change fabric roll width to suit a plenum chamber width change (different stencil/product), complete
the following remove and replace procedures.
NOTE
If changing fabric roll for a different stencil/product, ensure that the fabric roll width matches the
width of the plenum chamber.
3.6.1.1 Fabric Roll Removal
To remove the fabric roll, carry out the following:
1. Select Open Cover Commands.
2. If the stencil is covering/obstructing access to the cleaner, continue at Step 3.
If the cleaner can be accessed without moving the stencil, open the printhead cover and con-
tinue at Step 7.
3. Select Unload Screen.
4. Open the printhead cover.
5. If necessary, push the stencil towards the rear of the machine to improve access to the
cleaner.
NOTE
It may be necessary to completely remove the stencil from the machine.
6. Select Cleaner Functions button.
7. Select Change Paper.
8. Remove the used fabric take-up roller (1):
– Push the fabric take-up roller towards the left-hand end of the USC.
– Angle the fabric take-up roller and lift out of the printer.
1
9. Remove the empty fabric roll (2):
– Push the empty roll towards the left-hand end of the USC.
– Angle the empty roll and lift out of the printer.