PS288_OwnersMnl_PriorTo2009 - 第44页

Set Up • (Optional) Setting Up the Tape Input Feeder 2—10 PS288 Owner’s Manual Before running a job for the first time, it is necessary to: • T each locations to the PNP head. For information, see “T each the Pack- age F…

Set Up • (Optional) Setting Up the Tube Input and Tube Output Modules

PS288 Owner’s Manual 2—9

5b) Adjust the output tube unloader platform front and rear tube guides as

described in Step 4 above.

6. Insert tubes—

6a) Insert full tubes into the input tube loader platform.

6b) Insert empty tubes into the output tube unloader platform.

6c) Close the safety shield.

NOTE: The pin 1 orientation for devices is set in the package file.

Devices should be loaded in tubes as defined in the package file.

NOTE: If this is the first time you are installing tube feeders on

your PS288, you may need to edit the WinAH400.ini file to reflect

this additional option. Proceed with Step 7.

If you have previously installed tube feeders on your PS288, skip to

Step 8.

7. Configuring AH500 after first tube feeder installation—

7a) Make a backup copy of WinAH400.ini: e.g., WinAH400backup.ini.

7b) Using Windows Explorer, open C:\AH400_32\WinAH400.ini.with

NOTEPAD editor.

7c) Locate the section

;------- tube media settings -----

7d) Ensure that the value for Tube Feeder 1 (input tube feeder) is

STDIN. Change if it is not.

7e) Ensure that the value for Tube Feeder 2 (output tube feeder) is

STDOUT. Change if it is not.

7f) Save the WinAH400.ini file and exit Windows Explorer.

8. Configuring AH500 after repeat tube feeder installation—

8a) On the Options window, select "Tubes" for the input and output media.

8b) If the vision system will be used to check every device, set Vision Sys-

tem to ON.

8c) If the vision system will be used to check only the first and last devices

in a tube, set Vision System to OFF and check “1st +last 2 /tube.”

9. Adjust vibration controls—

If devices do not travel freely in the input tubes or the output tubes,

increase the vibration by turning the vibration controls clockwise. The

magnitude of vibration is set by adjusting V1 for the input tubes and

V2 for the output tubes.

NOTE: Within AH500’s Gantry window, Vibrator 1 is represented

by the yellow position label Vib1. Vibrator 2 is represented by the

yellow position label Vib2.

This completes the procedure for setting up a tube input and tube output

modules.

Set Up • (Optional) Setting Up the Tape Input Feeder

2—10 PS288 Owner’s Manual

Before running a job for the first time, it is necessary to:

• Teach locations to the PNP head. For information, see “Teach the Pack-

age File” on page 3-33.

(Optional)

Setting Up the

Tape Input

Feeder

The PS288 can be configured with an optional tape input feeder. The tape

input feeder is installed on the front of the PS288.

Tape input feeders are available in 8, 12, 16, 24, 32, 44, and 56 mm sizes to

match device tape of those widths. The last two digits of the tape input

feeder part number indicate the tape width. For example, a 32 mm tape input

feeder has a part number ending in 32. See Figure 2-11.

Figure 2-11—Part number for 32 mm feeder

To install the tape input feeder:

1. For first-time installation—

If the tape input feeder is being installed for the first time on your

PS288, the WinAH400.ini file may need to be edited to reflect this

additional option.

1a) Using Windows Explorer, open C:\AH400_32\WinAH400.ini with

NOTEPAD editor.

1b) Locate the section

;------- tape input/output -----

1c) Ensure value for Tape Advance Installed is TRUE, as shown.

TapeAdvanceInstalled=TRUE

1d) Save the WinAH400.ini file and exit Windows Explorer.

2. Prepare the system—

2a) From the Handler Computer interface, stop any Job that is running and

exit to the main window as shown in Figure 2-12.

Part number

Set Up • (Optional) Setting Up the Tape Input Feeder

PS288 Owner’s Manual 2—11

Figure 2-12—Main window

2b) Remove the two screws holding the small safety shield that covers the

tape input feeder slot.

Figure 2-13—Remove two screws holding small safety shield

2c) Remove the small safety shield and set it aside. It is not used when the

tape input feeder unit is installed.

3. Mount the feeder unit—

3a) Align the rail on the bottom of the feeder unit with the channel in the

base plate.

3b) Slide the feeder unit down the channel until the feeder unit reaches the

front wedge. See Figure 2-14.