Apollo1_Operators_Manuel - 第83页

83 cab - Produkttechnik GmbH / Tharo Systems, Inc. Rewinding Directly onto the Rewind Axle Fig. 13 f Rewinding directly onto the rewind axle 1. Attach the rewinder to the Apollo by positioning the metal posts on the bott…

82 cab - Produkttechnik GmbH / Tharo Systems, Inc.

If you have switched the operating voltage of your rewinder you need to

replace the fuses. For the standard setting of 230V, two fuses rated at

500mAT must be used. For operation at 115V, two fuses rated at 1AT must

be used. (Both types of fuses are shipped with the rewinder, one of

which is installed depending on the voltage setting.)

To alter the voltage, open the cover (3) and remove the voltage selector.

Replace the fuses as explained above. Slide the voltage selector back into the

power supply module so that the correct voltage is visible in the lid window.

Connect the rewinder to a grounded outlet using the power cable supplied in the

accessories package.

Connecting the Rewinder to the Power Supply

The rewinder operates with a supply voltage of 230V/ 50Hz or 115V/ 60Hz.

Before connecting the rewinder to the power supply, make sure that the

voltage selected on the power supply module is the same as your main

power supply !

Fig. 13 e Power supply module of the external rewinder

1 - Power supply

connector

2 - Power switch

3 - Voltage selector cover

The current voltage setting of the power module is visible in the lid window (3).

1 2 3

cab - Produkttechnik GmbH / Tharo Systems, Inc.

Rewinding Directly onto the Rewind Axle

Fig. 13 f Rewinding directly onto the rewind axle

1. Attach the rewinder to the Apollo by positioning the metal posts on the

bottom of the rewinder (5) into the holes of the adapter plate (4).

2. Feed the label strip over the guide bar and under the roller onto the

rewinder axle (6) as shown in Figure 13 f.

3. Considering the required method of rewinding, secure the label strip appro-

priately to the rewinder axle (6) by sliding the clamp (7) over the label strip

with the clamp set in the groove. (the broken line shows the path of inside

rolled labels)

Ensure that the label strip is even with the disc (1).

4. Slide the clamp (7) as far as possible towards the disc (1).

5. Slide the flange (3) onto the rewind axle (6) so that it slightly touches the

label strip. The label strip must be able to move slightly between the disc

and the flange.

6. Tighten knurled screw (2) in the flange (3).

7. Switch the rewinder ON.

Caution !

When switched ON, the rewinder immediately starts rotating !

457 6

84 cab - Produkttechnik GmbH / Tharo Systems, Inc.

1. Use a cardboard roll (5) which is about .04 in (1 mm) wider than the label strip.

2. Attach the rewinder to the Apollo by positioning the metal posts on the bottom

of the rewinder (4) into the holes of the adapter plate (3).

3. Mount the first axle adapter (6) onto the rewinder axle (2) and slide it up to the

disc (1). Tighten knurled screw (7).

4. Mount the second adapter onto the rewinder axle (2). Slide it towards the first

adapter until the clearance between the edge of the adapter and the disc (1)

is a little less than the width of the cardboard roll (5). Tighten knurled screw

(7).

5. Slide the cardboard roll (5) over the two adapters (6) until it is touching the disc

(1).

6. Feed the label strip over the guide bar and under the roller as shown in Figure

13 g up to the cardboard roll (5).

7. Using adhesive tape or a label, affix the end of the label strip to the cardboard

roll (5). (the broken line shows the path of inside rolled labels)

8. Slide flange onto the rewind axle (2) until it stops at the cardboard. Tighten

knurled screw.

9. Switch the rewinder ON.

Caution !

When switched ON, the rewinder immediately begins rotating !

Fig. 13 g Rewinding onto 3 in (75 mm) cardboard cores

(view without flange)

Rewinding on to 3 in (75 mm) Cardboard Rolls

6 57 4 3

1 2