00193796-08 - 第36页

Installation Manual Station Software Version 505.04 36 of 156 Menu item Note Selection options Virus Warning If the option is enabled, you will receive a warning if a program wishes to write to the boot sector or the par…

100%1 / 156
Installation Manual, Station Software Version 505.04 Edition 07/2006
35 of 156
4.3.1.6 Base, Extended, Total Memory
The type and size of the recognized DRAM memory is indicated here.
Base Memory
Memory below 1 Mbyte without the adapter hole (usually 640 kbyte)
Extended Memory Available memory above 1 Mbyte
Total Memory
1
Total memory, sum of all areas
4.3.1.7 Setup page "BIOS Features Setup"
This option comprises configuration entries which enable enhanced performance or customized
setting of the system.
In the "Selection options" column, the setting for fail-safe default is indicated in italics and the setting
for optimized default is underlined
.
1
Note that less memory is indicated here than is installed, as the onboard graphics controller reserves 1Mbyte of
the main memory for itself
Installation Manual Station Software Version 505.04
36 of 156
Menu item Note Selection
options
Virus Warning
If the option is enabled, you will receive a warning if a
program wishes to write to the boot sector or the partition
table of the hard disk.
Enabled
Disabled
CPU Internal Cache
1)
This option allows the internal cache to be enabled or
disabled.
Enabled
Disabled
External Cache
1)
You can enable the external cache here. Enabled
Disabled
CPU L2 Cache ECC
Checking
The ECC checking function of the level 2 cache of the CPU
can be set here.
Enabled
Disabled
Quick Power On Self
Test
This field enables the self-test to be speeded up when you
power on the computer (POST), by dispensing with a
second, third and fourth test of the SDRAM. For each test,
the system is tested once completely.
Enabled
Disabled
First Boot Device
First device from which to boot Floppy; LS120;
HDD-0; SCSI;
CDROM; HDD-1;
HDD-2; HDD-3;
ZIP100; USB-
FDD; USB-ZIP;
USB-CDROM;
USB-HDD; LAN;
Disabled
Second Boot Device
Second device from which to boot Floppy; LS120;
HDD-0
; SCSI;
CDROM; HDD-1;
HDD-2; HDD-3;
ZIP100; USB-
FDD; USB-ZIP;
USB-CDROM;
USB-HDD; LAN;
Disabled
Third Boot Device
Third device from which to boot Floppy; LS120;
HDD-0; SCSI;
CDROM; HDD-1;
HDD-2; HDD-3;
ZIP100; USB-
FDD; USB-ZIP;
USB-CDROM;
USB-HDD; LAN;
Disabled
Other Boot Device
If none of the set boot devices were found, a search is
made for all possible devices which can be set as a boot
device in one of the three options above, if this entry is set
to Enabled.
Enabled
Disabled
1)
Enabled caches enhance system performance
Installation Manual, Station Software Version 505.04 Edition 07/2006
37 of 156
Menu item Note Selection
options
Swap Floppy Drive
If the drive letters assigned to floppy drives are to be
exchanged, this field must be set to Enabled.
Enabled
Disabled
Boot Up Floppy
Seek
If this option is enabled, the BIOS looks for the floppy
drive A once
Enabled
Disabled
Boot Up Numlock
Status
The user can enable the NumLock function here (numbers
on the numeric block on the keyboard) when the system
boots.
On
Off
Gate A20 Option
When Fast is set, the keyboard controller switches Gate
A20, otherwise the processor does this.
Normal
Fast
Typematic Rate
Setting
When this field has been enabled, the following two
keyboard settings appear.
Enabled
Disabled
Typematic Rate
(Chars/Sec)
This field controls the speed at which the system registers
a key which is pressed and held as a keystroke.
6; 8; 10; 12; 15;
20; 24; 30
Typematic Delay
(msec)
This field controls the delay before keystrokes begin to
repeat.
250; 500; 750;
1000
Security Option
This determines when the system requests the password
(password: see PASSWORD SETTING).
System: The password is requested every time the system
boots.
Setup: The password is only requested when you call the
Setup utility.
Setup
System
APIC Mode
Under Windows 2000 and Windows XP, more interrupts
are available when this option is enabled
Disabled
Enabled
MPS Version
Control For OS
1.1
1.4
OS Select For
DRAM > 64MB
If the system operates under OS/2 with main memory
greater than 64 MB, this option must be set to OS2.
Non-OS2
OS2
HDD S.M.A.R.T
Capability
SMART (Self Monitoring Analyse and Reporting
Technology) is implemented in modern hard disks. This
technology can detect reading or rotational speed
problems. Data is read with the appropriate software.
Disabled
Enabled