00193796-08 - 第69页
Installation Manual, Station Software Version 505.04 Edition 07/2006 69 of 156 4.4.1.13 Setup page "COM Redirection" ┌─────────┤ COM Redirection ├───────────┐ │ │ │ ┌─ Status ───────────────────┐ ╔══════╗ │ │ │…
Installation Manual Station Software Version 505.04
68 of 156
4.4.1.12 Setup page "IMC Interrupts"
┌─────────────────────┤ IMC Interrupts ├────────────────────────┐
│ │
│ ┌───────────────────────────────────────────────┐ ╔══════╗ │
│ │ PC-IRQ IRQ-Source IRQ-Mode │ ║ OK ║ │
│ │ 3 onboard COM transparent │ ╚══════╝ │
│ │ 4 onboard COM transparent │ ┌──────┐ │
│ │ 5 SMP_INT2 transparent │ │CANCEL│ │
│ │ 6 onboard Floppy transparent │ └──────┘ │
│ │ 7 not assigned transparent │ ┌───────┐ │
│ │ 10 SMP_INT5 transparent │ │Default│ │
│ │ 11 SMP_INT6 transparent │ └───────┘ │
│ │ 14 onboard IDE transparent │ │
│ └───────────────────────────────────────────────┘ │
│ │
│ │
│ Press [F1] key for help │
└───────────────────────────────────────────────────────────────┘
The electronic interrupt matrix is to be set up as follows on this page.
PC-IRQ IRQ-Source
3 through 14 Unassigned
3
Onboard COM
4
Onboard COM
5 SMP_INT2 SMP16 interrupt c19
6 Onboard Floppy Floppy interrupt
7
Not assigned
10 SMP_INT5 SMP16 interrupt c25
11 SMP_INT6 SMP16 interrupt c27
14 Onboard HD Hard disk interrupt
IRQ-Mode
Transparent Interrupt line is connected through to the interrupt source (default)
Installation Manual, Station Software Version 505.04 Edition 07/2006
69 of 156
4.4.1.13 Setup page "COM Redirection"
┌─────────┤ COM Redirection ├───────────┐
│ │
│ ┌─Status───────────────────┐ ╔══════╗ │
│ │ ( ) disabled │ ║ OK ║ │
│ │ ( ) enabled │ ╚══════╝ │
│ │ (*) enabled (ANSI/VT100) │ ┌──────┐ │
│ └──────────────────────────┘ │Cancel│ │
│ ┌─Baudrate─────────────────┐ └──────┘ │
│ │ ( ) 9600 Bd │ │
│ │ (*) 19200 Bd │ │
│ │ ( ) 38400 Bd │ │
│ └──────────────────────────┘ │
│ ┌─Mode──────────────────────────────┐ │
│ │ (*) Autoredirection │ │
│ │ ( ) Redirect on Request only │ │
│ └───────────────────────────────────┘ │
│ Press [F1] key for help │
└───────────────────────────────────────┘
ANSI/VT100 must be selected in the "Status" field, as this makes it possible to operate the system
without a keyboard without errors. If this is not done, the BIOS reports a "Keyboard Error" on
booting.
Installation Manual Station Software Version 505.04
70 of 156
4.4.1.14 Setup page "IMC Miscellaneous"
┌─────────────────┤ IMC Miscellaneous ├────────────────┐
│ │
│ ┌─Keyboard───────────────────────────────┐ ╔══════╗ │
│ │[ ] Disable CTRL-C/CTRL-BREAK │ ║ OK ║ │
│ │[√] Force Cold boot on CTRL-ALT-DEL │ ╚══════╝ │
│ └────────────────────────────────────────┘ ┌──────┐ │
│ ┌─BIOS-E-Segment─────────────────────────┐ │Cancel│ │
│ │[√] Disable BIOS E-Segment at boot │ └──────┘ │
│ └────────────────────────────────────────┘ │
│ │
│ Press [F1] key for help │
└──────────────────────────────────────────────────────┘
Keyboard
Disable CTRL-C/
CTRL-BREAK
When this option is selected, the keystrokes <CTRL-C> and <CTRL-
Break> are trapped by the BIOS and not passed on to the operating
system.
Force Cold boot
on
CTRL-ALT-DEL
When this option is activated, pressing CTRL-ALT-DEL causes a
hardware reset rather than a warmstart.
BIOS-E-Segment
Disable BIOS
E-Segment at
boot
If this option is activated, the E-segment of the BIOS will be deactivated
prior to booting. Any access in this area will be passed on to the PCI bus
and thus to the ISA or SMP16 bus.
(interface to the axis cards)
4.4.2 Hard disk partitioning
Partitioning required for the hard disk:
C: partition 50 MByte, active boot partition
D: partition 450 MByte, SIPLACE Software
The total size of both partitions must not exceed 504 Mbyte.
The DOS program fdisk is used for partitioning.
It can be called via the command line after booting with a DOS system floppy or will start automatically
when the operating system is installed if the hard disk was not set up correctly.