00197501-02_AI_WPC_Umbau_X-Series_S_DE_EN - 第68页

Review 3 Setting up and Commissioning 3.1 Removing the Standard Component Trolley Feed Device 68 Assembly Instructions / Montageanleitung SIPLACE WPC an SIPLACE X-Serie S SIPLACE WPC on SIPLACE X Series S 03/2020 3.1 Rem…

Review

3 Setting up and Commissioning



Assembly Instructions / Montageanleitung SIPLACE WPC an SIPLACE X-Serie S SIPLACE WPC on SIPLACE X

Series S 03/2020

3 Setting up and Commissioning

When operating the SIPLACE WPC5/WPC6 on an SIPLACE X-Series S, you need to fit a fixed

table.

► First remove the standard COT insert (COTi-40). Then fit the fixed table with SIPLACE WPC

[03110607- xx] for the SIPLACE WPC5/WPC6.

► If not already present, fit a service flap. For details, read the assembly instructions for the

"Service flap X-Series S" [00197396-xx].

► See also the assembly instructions "SIPLACE X‑SeriesS input/output conveyor extension and

hand guard" [00197089‑xx]

► For conversion of the waste slide, refer to the chapter 3.5 "Fitting the Waste Tape

Slide" [}77].

► When operating the SIPLACE WPC5/WPC6 on the SIPLACE X-Series S, you also need to fit

a hand guard on the SIPLACE WPC. See also the chapter 3.4

"Fitting the bridge cover

SIPLACE WPC on the SIPLACE X-Series S" [}76].

► If an MTC2 was already fitted to the machine, you will also need to replace the slanted cover

guide with a straight one. See also the assembly instructions "SIPLACE X-Series S MTC2 on

location 2" [00197082-xx].

Review

3 Setting up and Commissioning

3.1 Removing the Standard Component Trolley Feed Device

68 Assembly Instructions / Montageanleitung SIPLACE WPC an SIPLACE X-Serie S SIPLACE WPC on SIPLACE X

Series S 03/2020

3.1 Removing the Standard Component Trolley Feed Device

WARNING

Risk of injury when working near the tape cutter.

When working in the area of the tape cutter, move the component trolley out of the machine

and disconnect the machine from the mains supply and the compressed air supply.

► Wait until the operating pressure has dropped to 0 MPa.

► Always secure the machine against unauthorized reactivation.

► Do not reach into the tape cutter.

CAUTION

Risk of injury when performing service work on the tape cutter.

Never support the tape cutter on your body, e.g., on your knees or thighs. Do not place

your feet under the tape cutter.

► Wear appropriately thick protective gloves.

► When removing/fitting the tape cutter, hold it only outside on the left and right.

Fig.11: COT insert

1. COT insert

CAUTION

Heavy machine part!

The COT insert is heavy. To lift it out, you will need to use the mounting tool and a suitable

lifting device (hand-operated crane etc.).

Removal

► Switch off the machine, disconnect it from the power supply and secure it to prevent

unauthorized reactivation. See also section 1.2

"Preparatory work..." [}56].

► Dismantle the nozzle changer.

► Disconnect the COT insert from all electrical and pneumatic connections. Mark the positions

of these connections, to make clear assignment easier later on. The connection cables and

hoses are located behind the COT insert – in the space leading to the machine base (under

the nozzle changer). See also the chapter 5.1.3

"Nozzle Changers and Nozzle Stations -

Overview" [}89].

► Dismantle the left side cover. See also the chapter 5.1.4 "Dismantling the Lower Side

Cover" [}91].

► Unhook the middle cover.

Review

3 Setting up and Commissioning

3.1 Removing the Standard Component Trolley Feed Device

Assembly Instructions / Montageanleitung SIPLACE WPC an SIPLACE X-Serie S SIPLACE WPC on SIPLACE X

Series S 03/2020

Fig.12: Assembly lifting device and mounting tool

1. Fixtures

2. Mounting tool

3. Eyelet

► Attach the mounting tool (2) to the fix-

tures provided (1)

on the COT insert.

► Fix the lifting device to the eyelet (3) of

the mounting tool (2)

 NOTICE!

The COT insert can be installed at dif-

ferent positions in the machine loca-

tion. Mark the position of your COT in-

sert, to ensure that this is sub-

sequently returned to its original posi-

tion.

Fig.13: Lifting out the COT insert

► Loosen the screws fastening the COT

insert(1)

► Lift the complete COT insert out of the

machine and place it on a suitable sur-

face (four wooden blocks etc.).

► Make sure that you do not damage any

valves, connection cables, hoses etc.