N7201A617E00_0317 - 第27页
NPM-W 2 EJM7DE-SF-01N-0 0 CA UTION 1-1 -8 Observe the precautions described in the Product’ s [Safety Data Sheet] (Cause of inju ry or damage by ch emical substances) ● Safety Data Sheets can be foun d in the [Maintenanc…
NPM-W2 EJM7DE-SF-01N-00
Safety precautions 4
1-1
Be sure to ground the
machine
(Risk of electric shock or leak)
●Consult a professional electrical
contractor.
1-1-7
Do not place your hands or
body into the moving parts
of the machine even while
the machine is stopped
(Risk of injury)
●When the machine is in single stop or
cycle stop state, moving parts of the
machine may start running unexpectedly
if the sensors are activated.
When moving an feeder
cart, pay careful attention
to your surroundings
(Risk of injury due to crashing into
people)
Do not touch the cutter part
or the sheet-metal edge
part of the feeder
(Risk of cutting fingers or hands)
Be careful not to get your
fingers or hands caught
(Risk of injury)
●This graphic symbol, a warning label, is
put on parts which contain the potential
risk of catching fingers or hands.
Do not touch an electrified
part with conductive
materials such as a wire
(Risk of electric shock)
●Current-carrying parts including the
connector and the terminal.
Take care not to
receive an electric
shock
(Risk of electric shock)
●This graphic symbol, a warning label,
is put on parts which carry the
potential risk of electrical shock.
Do not operate the
machine without
receiving special
training
(Risk of injury due to uncontrolled or
incorrect motion of the machine
caused by improper operation)
●Contact us about training.
Take care not to
touch hot surfaces
(Risk of burns)
●This graphic symbol, a warning label,
is put on parts which may increase in
temperature.
●They may remain heated even after
stopping operation.
Do not put your
hands in the
openings between
feeders installed
(Risk of injury due to the contact with
the moving part inside the machine)
●We recommend installing all feeders
so that you will not accidentally put
your hands into the machine.
Take care not to punch
your hand
(Risk of injury)
●This graphic symbol, a warning label, is
put on parts which contain the potential
risk of squeezing hands.
●Direct particular attention to any of the
following.
・When closing the cover.
・When adjusting the width between
rails manually or automatically.
・When moving XY table, the head and
the axis by hand.
WARNING
Feeder
mounting
area
NPM-W2 EJM7DE-SF-01N-00
CAUTION
1-1-8
Observe the precautions
described in the Product’s
[Safety Data Sheet]
(Cause of injury or damage by chemical
substances)
●Safety Data Sheets can be found in the
[Maintenance manual].
Wear a cloth hat or helmet
and protective goggles
during maintenance work
(Risk of injury)
●Motor or control boxes.
Handle the feeder carefully
when carrying it
(Risk of injury/backache due to dropping)
●Handle properly in accordance with the
manual.
Do not apply any impact to
motors or other electrical
equipment
(Risk of electric shock, cause of electrical
leakage)
●Motor or control boxes.
Do not climb on equipment,
peripheral devices and
moving parts
(Cause of damage by load or injury by
failing or being stuck in the equipment)
●Covers, the feeder cart and inspection
box.
Be sure to observe the following
Do not put any
objects around
emergency stop
switches
(Risk of an accident due to being
unable to press the switch to stop the
machine in case of emergency)
Confirmation
To prevent
injury or
electric
shock…
NPM-W2 EJM7DE-SF-01N-00
C
Warning labels 1
Danger labels
1-2-1
Follow the instructions on labels on the locations below.
If it has come off, place an order with us for it, referring to its label No. in the Parts List; then, put the new one
on the proper location.
1-2
■NPM-W2 main unit
Front side
On the right edge of
the feeder cover
On the right edge of
the feeder cover
(*1) Labels are affixed
for feeder chart
specification
PD0101M1
(*1)
Front side Rear side