N7201A617E00_0317 - 第51页

NPM-W 2 EJM7DE-SF-01N-0 0 1-3-3 -2 NOTICE ● Be sur e to connect th e device or the conveyor satisfied the ma chine safety r equirements suc h as ISO13849-1 or IEC6201. ● Keep the safety distance of 600 mm or more from th…

NPM-W2 EJM7DE-SF-01N-00

Connecting a device or a

conveyor prepared by

customer

1-3-3-1

The NPM-W2 has a PCB transfer opening on the left and right sides. Since the front and rear heads in the

machine move within the area shown below at high-speed, it is very dangerous if you insert your hands into

the machine. If you couple a device or a conveyor prepared on your own, be sure to provide safety

measures.

1-3-3

Front side Rear side

Safety

manage-

ment

125 mm

622 mm

102 mm

622 mm

102 mm

Head movable area

NPM-W2 EJM7DE-SF-01N-00

1-3-3-2

NOTICE

●Be sure to connect the device or the conveyor satisfied the machine safety requirements such as

ISO13849-1 or IEC6201.

●Keep the safety distance of 600 mm or more from the opening in order not to reach hands into the

opening of the NPM-W2 from the adjacent device or conveyor. (Reference (1))

●If you can keep only the safety distance of 400 to 600 mm from the opening of the NPM-W2, install the

safety sensor on the PCB transfer opening, and output the safety support signal to the NPM-W2.

(Reference (2))

●Take measures not to insert hands or fingers from the space between the NPM-W2 and the device or

the conveyor.

●Install the full cover that usually you cannot open or close, to the transfer rail of the device or the

conveyor.

If you can reach the PCB transfer opening with the open/close cover installed, install the safety switch,

and output the safety support signal to the NPM-W2 while the cover is open. When the cover is open,

the NPM-W2 stops for confirming safety.(Reference (3))

●About detailed conditions regarding machine safety or safety about connection with machines

manufactured by us (CM series), please ask us.

PCB transfer opening PCB transfer opening

Peripheral

equipment

(conveyor)

Peripheral equipment

(placement machine)

(1) 600mm or more

(2) If the space is only 400 to

600 mm, the transfer

opening sensor is

necessary

(1) 600mm or more

(2) If the space is only 400

to 600 mm, the transfer

opening sensor is

necessary

(3) Full cover

●Safety switch is required

for the open/close cover

Confirmation

NPM-W2 EJM7DE-SF-01N-00

1-4-1

Precautions 1

1-4

Precautions in use

●Do not move noise sources such as welders close to equipment. A malfunction may occur.

●During the operation of equipment, avoid turning OFF the power switch of the main controller, the servo

switch and the air unnecessarily.

Because equipment operates independently without being controlled, breakage may occur.

●During instruction or when moving a unit with the servo free from stress, be sure that there is no

interference. Breakage may occur.

●The tray feeder cover is locked with a cylinder. Forcing open the cover may cause breakage of the cover

or the cylinder.

●Do not take apart or alter the main body of equipment or the unit. It may affect the level of safety and

quality control of products.

●Data should only be changed by authorized personnel, who have received special training.

A malfunction may occur due to improper input.

●Do not block the fan outlet and inlet. Abnormal action arising from the increase in temperature inside the

control box may occur.

●Do not turn OFF the servo switch during operation. It may cause machine to malfunction. Turn it OFF

when the machine is in a temporary stop state (single stop or cycle stop) or operation stop state.

●When the nebulizer or the humidifier are used, be aware of quality of water. Especially using the ultrasonic

humidifier, calcium and magnesium of components of hardness, and silica, carbonate and iron are

discharged in the air depending on quality of water. Adhesion of power dust to the machine can cause

sliding or optical dysfunctions.

●Do not use the machine in the environment that low molecular weight siloxane is found due to gasification

of silicon materials (silicone adhesive, silicone oil and silicone power.)

Adhesion of low molecular weight siloxane to the electrical contact part or optical part of the machine can

cause contact or functional defects.

●We have no responsibility regarding the followings.

・ Improper usage, and trouble and damage due to inappropriate repair or remodel

・ Accidental damage arising from the machine use or fail such as loss of business interests, or change

or deletion of memory data

・ Trouble or damage caused by relocation, transportation or drop of the machine after purchased

・ Trouble or damage caused by fire, an earthquake, flood damage, lighting strike or any other act of

providence, and environmental pollution, salt pollution, gas pollution (Corrosive gas and halogen gas),

abnormal voltage and power supplies, other than specified (voltage, frequency)

・ Trouble and damage arising when transported by vehicles and ships

・ Damage arisen from not being observed described matters in the manuals included in this product