00197196-02_VB_SetupCenter_5.1_de_en - 第49页
Restrictions SIPLACE Pro Restrict ion Version Description / Versions beschreibung SIPLACE Setup Center 5.1 49 6 Restrictions 6.1 Restriction 6.1.1 SIPLACE Pro ▪ The following SIPLACE Pro versio ns are not supported any l…
New Functions in Setup Center 5.1
Bluetooth Barcode Scanner Supported Permit Packaging Unit Chains to be Split in the Packaging Unit Editor
48 Version Description / Versionsbeschreibung SIPLACE Setup Center 5.1
5.5 Bluetooth Barcode Scanner Supported
Purpose
The Datalogic Bluetooth
TM
barcode scanner Datalogic PowerScan® BT8300 (1D barcode) is supported.
You also need the base unit BC-8030-BT.
Each Setup Center application supports one base unit with up to four registered PowerScan BT8300 bar
-
code scanners.
Configuration
► In the main menu open Extras > Settings and the Settings window is opened.
► Select the category Scanner and the settings are opened.
► Go to Datalogic Scanner and select Connect Barcode Reader...
► The start page for the installation procedure will open.
► For detailed information, refer to the user manual "Setup Center 5.1".
5.6 Improved Table Management
Function – for forced setup verification
If the changeover table management is active, you need to scan in the table ID. The table ID is then
shown in the graphical view of the table in Setup Center.
If a setup changeover is then performed, the tables will no longer be switched over to offline mode but
will remain logged on. This means that the tables are no longer moved out and do not need to be logged
on again.
Restrictions
SIPLACE Pro Restriction
Version Description / Versionsbeschreibung SIPLACE Setup Center 5.1 49
6 Restrictions
6.1 Restriction
6.1.1 SIPLACE Pro
▪ The following SIPLACE Pro versions are not supported any longer:
– SIPLACE Pro 3.2
– SIPLACE Pro 4.1
6.1.2 Station Software
▪ The following station software versions are not supported any longer:
– 604.xx
6.1.3 Database Views
▪ The following Setup Center database views are not supported any longer:
– v_PackagingUnitInSetup_Short
– v_PackagingUnitInSetup
– v_PackagingUnitInSetup2
– v_PackagingUnitInSetup3
– v_PackagingUnit
– v_PackagingUnit2
– v_PackagingUnit3
– v_PackagingUnit4
– v_PackagingUnit5
– v_PackagingUnitInUse
– v_PackagingUnitInUse2
– v_TableInventory
– v_VerificationHistory
A part of the existing interface is lost because of the omission of the views named above. Due to
the modified database scheme, however, it is not possible to offer the views any longer.
6.1.4 Windows Vista / 64 Bit Operating Systems
▪ The WLAN modules Scalance W788/W744 cannot be configured on 64 Bit operating systems with
the PST tool.
6.1.5 Splice Points
▪ When using splice sensors don't repair damaged packaging units with splice because repair splice
points cannot be distinguished from the normal splice points.
NOTICE
The data access via OIB interface is recommended.
Restrictions
Known Facts / Problems (General) Traceability
50 Version Description / Versionsbeschreibung SIPLACE Setup Center 5.1
6.1.6 Traceability
▪ The component level indicator for the machines of the S, F, HS and HF series recognizes identical
packaging unit information and ignores it. The menu field "Unique ID" must therefore always be
transferred into a Traceability data field.
▪ The settings "Identical Component Lot for linear feeders" and "Identical Component Lot for tray
changers" store the scanned "Unique ID" in the data field "Batch". The Traceability data for the con
-
figured "Unique Id" and "Batch" barcodes will therefore both show the "Unique ID".
6.1.7 Set-Up Sheet
▪ Setup Center prints barcodes exclusively of the type Code-39. This type masters the following valid
characters: 0123456789 [space character] ABCDEFGHIJKLMNOPQRSTUVWXYZ-.$/+%. Other
characters are displayed as gap in the barcode and the barcode printout are not readable.
▪ When SIPLACE Pro 5.0 SP1 SP1 is used, the setup lists printed out do not contain graphics of the
components.
6.1.8 Recovery Placement
▪ Due to the restart of the machine, the value for the consumption of already placed components on
the boards that are not finished yet is lost.
6.1.9 X And SX Docking Station
▪ Before starting Setup Center all X docking stations connected via the CAN bus must be online.
Only then it is possible for Setup Center to recognize the type of the docking station correctly.
▪ In order to verify the tracks of a changeover table with 30 tracks, the feeders must first be placed
onto tracks 31 to 60 of a 60 track wide changeover table in the docking station and then be verified.
After that, the feeders must be replaced onto the 30 track wide changeover table.
6.1.10 Mat Label
▪ The barcode parts are invariably described in the Barcode Rules Editor.
6.2 Known Facts / Problems (General)
6.2.1 Update Installation
▪ We recommend that you perform a complete backup of the Setup Center database before updating
to Setup Center 5.1.
▪ We recommend that you reduce the database to a minimum before updating to Setup Center 5.1
(see user manual: database maintenance).
▪ When updating the installation at least 1.7 times the size of the Setup Center database must be avail
-
able as free disk space.
▪ Depending on the size of the database and the hardware used, the database update can take up to
several hours.
▪ During the database upgrade the Setup Center GUI must not be started and no production must be
in progress.