00191134-03 - 第60页
GEM for SIPLACE V5.01 Page 60 of 252 ©Siemens AG, all rights reserved )HHGHU$FFHVVHV3HU3&% – Num ber of f eeder acc esses per PCB Format: U2 used in: PICKUPERRORS )HHGHU7\ SH Identif ier for a feeder Format: U2 1…
GEM for SIPLACE V5.01
©Siemens AG, all rights reserved page 59 of 252
2 = Denied. Invalid format
3 = Denied. At least one RPTID already defined
4 = Denied. At least one VID does not exist
>4 = Other errors
5 - 63 reserved
used in: S2F34
'63(5 Data Sample Period
Format: A
used in: S2F23
($& - Equipment Acknowledge Code
Format: B[1]
0 = Accept
1 = Denied. At least one constant does not exist
2 = Denied. Busy
3 = Denied. At least one constant out of range
>3 = Other errors
4 - 63 reserved
used in: S2F16
(&'() - Equipment Constant Default Value
Format:
used in: S2F30
(&0$; - Equipment Constant MaximumValue
Format:
used in: S2F30
(&0,1 - Equipment Constant Minimum Value
Format:
used in: S2F30
(&1$0( - Equipment Constant Name
Format:
used in: S2F30
(5$&. - Enable/Disable Event Report
Format: B[1]
0 = Accept
1 = Denied. At least one CEID does not exist
>1 = Other errors
2 - 63 reserved
used in: S2F38
)&1,' - Function Identification
Format: U1
used in: S2F43, S2F44
GEM for SIPLACE V5.01
Page 60 of 252 ©Siemens AG, all rights reserved
)HHGHU$FFHVVHV3HU3&%– Number of feeder accesses per PCB
Format: U2
used in: PICKUPERRORS
)HHGHU7\SHIdentifier for a feeder
Format: U2
1 Linear 4.5 mm
2 Linear 9.5 mm
3 Linear 10 mm
4 Linear 14 mm
5 Linear 30 mm
6 0402_0603
151 Fimecore
152 Nitto
7 8 mm tape, electric, 2 x cycle
8 8 mm tape, electric
9 8 mm tape, mechanical, 2 x cycle
10 8 mm tape, mechanical
29 8mm tape "long" 2mm manual
19 8mm tape "long" 4mm manual
149 8mm tape „long“ 8mm
150 8mm "Schulz" tape
11 12mm tape "long"
12 16mm tape "long"
14 24mm "Blister" tape
16 32mm "Blister" tape
15 32mm "Paper" tape
17 44mm tape
18 56mm tape
56 24mm type III
57 32mm type III
58 44mm type III
59 56mm type III
60 S_G_12_S
61 S_G_16_S
62 S_G_24_S
63 S_G_32_S
64 S_G_44_S
65 S_G_56_S
30 waffle-pack tray
153 bulk-case
used in: PICKUPINFO1REV1, PICKUPUPREV2, PICKUPIC
)LGXFLDO1DPHIdentifier of a fiduvial
Format: U2
used in: TAUGHTFIDUCIAL, FIDUCIALDATA
)RUFH,QGH[ - programmed placement force
see chapter 3.5 in the SIPLACE Data Interface for a detailed description.
Format: U1
used in: PLACEINFOREV1, PLACEINFOREV2
*$175<*5283,' – ID of the gantry-group
Format: U2
Not used.
GEM for SIPLACE V5.01
©Siemens AG, all rights reserved page 61 of 252
*$175<,' – ID of the gantry
Format: U2
0 = gantry on the left side in direction of transport
1 = gantry on the right side in direction of transport
*5$17 - Permission to send
Format: B[1]
0 = Permission granted
1 = Busy, try again
2 = Not interested
>2 = Other errors
3 - 63 reserved
used in: S6F6
+&$&. - Host Command Parameter Acknowledge Code
Format: B[1]
0 = Accept, Command has been performed
1 = Command does not exist
2 = Cannot perform now
3 = At least one parameter is invalid
4 = Acknowledge, command will be performed with completion signaled later by an
event
5 = Rejected. Already in desired condition
6 = control state is not remote
7 = recipe not in library
8 = control mode is not „GEM-Host“
9 = bad PP-Body
10 - 63 reserved
used in: S2F42
+($',' – ID of the head
Format: U2
0 = head (on the left gantry in direction of transport) with 12 segments on first
gantrygroup
1 = head (on the left gantry in direction of transport) with 6 segments on first
gantrygroup
2 = IC-head (on the left gantry in direction of transport) on first
gantrygroup
3 = head (on the right gantry in direction of transport) with 12 segments on first
gantrygroup
+(,*+72)5(92/9(5 distance between the head and the transport conveyor
During the reference run, the SIPLACE machines measures the difference between the
upper edge of the transport conveyor and the nozzle on segment 1. The
HEIGHTREVOLVER is then calculated by subtracting the length of the nozzle on segment
1 form the measured value. The nozzle length is defined in the machine data. So
HEIGHTREVOLOR is a relative, not an absolute value.