00191134-03 - 第67页
GEM for SIPLACE V5.01 ©Siemens AG, all rights r eserved page 67 of 252 56'& Request Spool Data Code Format: B[1] 0 = Transm it Spooled Massages 1 = Purge Spooled Messages 2 - 63 reserved 6(*0 (17 – Num ber of th…
GEM for SIPLACE V5.01
Page 66 of 252 ©Siemens AG, all rights reserved
4 = busy, try later
5 = will not accept
>5 other error
6 - 63 reserved
used in: S7F2
33,' - Process Program ID
Format: A[8]
used in: S2F27, S7F1, S7F3, S7F5, S7F6, S7F17, S7F20
357,' - Report ID
Format: U4
used in: S2F33, S2F35, S6F3, S6F9, S6F11, S6F13, S5F16, S6F18, S6F19, S6F21
4XDOLW\ - Measurement result of a package form or a fiducial
Quality ranges between 0 and 100. The higher the value, the better the fiducial was
recognized.
Format: U1
used in: PLACEINFOREV1, PLACEINFOREV2, FIDUCIALDATA
5&0' - Remote Command
Format: A
used in: SsF21, S2F41
5HDO1R]]OH/HQJWK - measured nozzle length
The nozzle length is measured during the reference run. It depends on the
HEIGHTREVOLER value. So REAL_NOZZLE_LENGTH is not a absolute but a relative
value.
It is calculated by subtracting the measured difference between the nozzle and the upper
edge of the conveyor belt from the HEIGHTREVOLER value.
Format: I4
Units are 1/1000 mm
5HIHUHQFH'HVLJQDWRU - Identifier for a placement position
Format: A
see chapter 5.4 in the SIPLACE Data Interface ( <position_name> in
<placemant_pos_record>).
used in: PLACEINFOREV1, PLACEINFOREV2, COORDINATEIC
5(3*6= - Reporting group size
Format: U4
used in: S2F23
56'$ - Request Spool Data Acknowledge
Format: B[1]
0=OK
1 = Denied, busy try later
2 = Denied, spooled data does not exist
3 - 63 reserved
used in: S2F24
GEM for SIPLACE V5.01
©Siemens AG, all rights reserved page 67 of 252
56'& Request Spool Data Code
Format: B[1]
0 = Transmit Spooled Massages
1 = Purge Spooled Messages
2 - 63 reserved
6(*0(17 – Number of the segment to pick up or place a component.
Format: U1
6+($' - Stored header related to the transaction timer
Format: B[10]
used in: S9F9
603/1 - Sample number
Format : U4
used in: S6F1
62)75(9 - Software revision code
Format: A[6]
used in: S1F2, S1F13, S1F14, S1F65, S1F66
67,0( - Sample time
Format: A[16]
used in: S6F1
675$&. - Spool Stream Acknowledge
Format: B[1]
1 = Spooling not allowed for stream
2 = Stream unknown
3 = Unknown function specified for this stream
4 = Secondary function specified for this stream
used in: S6F44
675,' - Stream ID
Format: U1
used in: S2F43, S2F44
69,' - Status Variable ID
Format
used in: S2F23
691$0( - Status variable name
Format: A
used in: S1F12
7(;7 - A single line of characters
Format: A[160]
used in: S10F1, S10F3, S10F5, S10F9
7,$$&. - Equipment Acknowledge Code
Format: B[1]
GEM for SIPLACE V5.01
Page 68 of 252 ©Siemens AG, all rights reserved
0 = everything correct
1 = too many SVIDs
2 = no more traces allowed
3 = invalid period
4 - 63 reserved
used in; S2F24
7,$&. - Time Acknowledge Code
Format: B[1]
0=OK
1 = Error, not done
2 - 63 reserved
used in; S2F32
7,' - Terminal ID
Format: B[1]
0 = single or main terminal
>0 = additional terminals on same equipment
used in: S10F1, S10F3, S10F5
727603 - Total sample to be made
Format: U4
used in: S2F23
7UDFN1XPEHU - Number of a track
Format: I2
used in: PICKUPINFO1REV1, PICKUPUPREV2, PICKUPERRORS
WROBGLUW\BQR]]OH - vacuum value
Format: I4
Units are mbar
used in : VACUUMDATEREV1, VACUUMDATAREV2, VACUUMDATAIC
WROBOHDN\BQR]]OH - vacuum value
Format: I4
Units are mbar
used in : VACUUMDATEREV1, VACUUMDATAREV2, VACUUMDATAIC
75,' - Trace Request ID
Format: U4
used in: S2F23 S6F1
81,76 - Units of measure
Format: A
used in: S1F12, S2F30, S2F48
833(5'% - Upper boundary of the dead-end of a limit
Format:
used in: S2F45, S2F48