YAMAHA 报警资料 - 第109页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 109 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 108 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Side View camera.
[Detail Mode] setting should measure the nozzle shape before
auto running.
If you already executed Measure Nozzle after the nozzle
combinations are changed then please select "No".
[Yes] Execution
[No] Cancel reconfirmation
于[有 ]，在运行前必先俘吸嘴形状。
吸嘴合更改后，已行吸嘴形状俘，[否]。
[是] 行
[否] 行取消再确
Ea07521 Confirm Auto Running
The side view measure nozzle was canceled.
Please confirm to start Auto Running.
[Yes] Start Auto Running
[No] Side view measure nozzle retry
制运行始的确
取消了面相机的吸嘴形状俘。
可以始运行?
[是] 始制运行
[否] 重新确面吸嘴形状俘
Ea07523 Nozzle Cleaning stop
It became nozzle washing time that had been set by the schedule
specification.
Please cleaning the nozzle of each head follow the manual.
吸嘴清停止
已到达度表程中所置的吸嘴清指定。
按照各 Head 的帮助主来行吸嘴清。
Ea07525 Confirm Nozzle cleaning finished
Was the nozzle cleaning finished?
[Yes] Start Auto Running.
[No] Stop Auto Running.
吸嘴清束确
吸嘴清束了?
[是] 始自运行。
[否] 停止自运行。
Ea07528 Side view camera nozzle dirt error
The nozzle dirt error was detected with the side view camera.
The operator is needed the [%d] nozzle washing of the head.
After mounting the board in the machine,
does execute the nozzle cleaning?
[Yes] After mounting, execute nozzle cleaning.
[No] After specified time, this warning is displayed again.
面相机 吸嘴垢
面相机到吸嘴垢。
有必要操作者清%s 号 Head 的吸嘴。
机器内基板理后行吸嘴清?
[是] 理完机器内基板后行清。
[否] 在指定后再次示警告。
Ea07529 It failed to measure the nozzle shape.
Side view camera detects nozzle shape error at %d head.
(Detail error: %d[%s] Nozzle: %s)
Please stop Auto-running, and confirm whether a nozzle does not
have some dust or damage.
Please confirm bellow also.
1. The head does not handle the nozzle correctly.
The Machine will stop measuring nozzle shape.
吸嘴形状俘已失。
用面相机俘吸嘴形状，在[%d]号装
出了吸嘴形状异常。(=%d[%s] 吸嘴%s)
停止运行，吸嘴是否有垢粘附、破。
此外，也有可能是因下列原因所致。
1. 再次确吸嘴是否已正确安装。
中止吸嘴形状俘。
Ea07530 It failed to measure the nozzle shape.
Side view camera cannot find nozzle tip at %d head.
(Detail error: %d[%s] Nozzle: %s)
Please stop Auto-running, and confirm that the head handle
the nozzle correctly.
Please confirm bellow also.
1. Please confirm whether the nozzle is not damaged.
2. Please confirm that the Multi camera light is flashed
on Adjust Assist.
The Machine will stop measuring nozzle shape.
吸嘴形状俘已失。
用面相机俘吸嘴形状，在[%d]号装没有
吸嘴前端。(=%d[%s] 吸嘴%s)
停止运行，确吸嘴是否已正确安装。
此外，也有可能是因下列原因所致。
1. 吸嘴前端是否已破。
2. 行助整，确照明是否亮着灯。
中止吸嘴形状俘。
Ea07531 It failed to Measure Nozzle
The [%d] nozzle was detected Nozzle Dirt error.
(Detail error number is [%d].)
It seems that nozzle tip is dusty.
Please confirm whether the nozzle is correctly installed again.
The Measure Nozzle is discontinued.
吸嘴形状俘已失。
[%d]号吸嘴生吸嘴垢。(=[%d])
吸嘴前端可能附有垢。
再次确是否安装了正常的吸嘴。
中止吸嘴形状俘。
Ea07532 It failed to measure the nozzle shape.
On the recognition of Side view camera, it happened internal error
at %d head.
(Detail error: %d[%s] Nozzle: %s)
This error may occur repeatedly.
Please record the head number and the detailed error number,
and inform to a maker.
The Machine will stop measuring nozzle shape.
If you want to continue running temporary then please set the follows
setting in Machine Setting.
Machine Setting - Side view camera - non
吸嘴形状俘已失。
用面相机，在[%d]号装生了内部。
(=%d[%s] 吸嘴%s)
此可能反生。
装号和号，并向制造厂商咨。
中止吸嘴形状俘。
此如将面相机功能置无效，可以
使机器运行。在向管理人确的基上，参照下列内容。
机器置-工厂置-面相机-「没有」
Ea07533 It succeeded to save the measured nozzle shape.
Because a part of measured nozzle size was out of the design value.
Please confirm the nozzle.
吸嘴形状的保存已成功了。
因一部分的吸嘴形状定在范外，
所以操作者取消了保存。
建您再次确吸嘴是否正常后重新始运行。
Ea07534 The Measure Nozzle was canceled.
The Measure Nozzle for the Side View was canceled.
取消了吸嘴形状的俘。
取消了由面相机的吸嘴形状定。
您确定?
Ea07535 The nozzle shape data was not saved.
The nozzle shape data was not saved because the operator selected
未能保存吸嘴形状数据。
由操作者取消了吸嘴形状数据的保存。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 109 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
cancel command.
Measure Nozzle was not save data.
不行吸嘴形状数据的保存。
Ea07536 It failed to measure the nozzle shape.
On the recognition of Side view camera, it happened nozzle fit error
at %d head
(Detail error: %d[%s] Nozzle: %s)
The nozzle tip position is detected as illegal value.
Please stop running, and confirm that the head handle the nozzle
correctly.
吸嘴形状的失了。
用面相机量%d 号装的吸嘴前端形状，
生了吸嘴配合。
(: %d[%s] 吸嘴: %s)
吸嘴前端或特征部的位置超了容。
吸嘴的安装可能不正确，
停止运行，吸嘴的安装状况。
Ea07537 It failed to measure the nozzle shape.
The nozzle of number %d head was not able to
be recognized by side-view camera.
(Detail error: %d[%s] Nozzle: %s)
Please confirm the following.
1. Is the nozzle correctly installed?
2. Does the side view lighting light?
Please record head number and detail error,
and contact the maker when this error occurs many times.
吸嘴形状的失了。
用面相机%d 号装的吸嘴，失了。
(: %d[%s] 吸嘴: %s)
确下列目。
1. 吸嘴的安装是否正确?
2. 面照明是否呈亮灯状?
如反生，
Head 号和号，向生厂商咨。
Ea07538 WATCH DOG - HEAD & FEEDER STATUS INCONSISTENT Head 的下降状和送料器的器状不一致
Ea07539 SHUFT CLEANING BLOW EXECUTION ERROR
Can't execute shuft cleaning blow of manual or fixed
nozzle.Please reload 'board data' and retry.
Execution condition
1. Not editing of 'board data'.
2. The error must not occur by data check of
the 'board data'.
吸嘴吸嘴排气清行
不能行固定/手更吸嘴的吸嘴排气清。
重新入基板程序后，重新行。
行条件:
1. 基板程序不能状。
2. 基板程序的程序中不能生。
Ea07540 NOZZLE CONDITION ALL CHECK RESULT
<<< WARNING >>>
After the error is cleared, the check result list is displayed.
Please clean the NG nozzle of the result before producing it.
Please confirm the state of the nozzle again after cleaning it.
And please check if the tip of the nozzle is broken.
吸嘴状全部果
<<< 警告 >>>
解除后示果列表。
生前、清果 NG 的吸嘴。
清后、再次确吸嘴的状。
并、确吸嘴的前端是否破。
Ea07541 VACUUM LEVEL ALL CHECK RESULT
<<< WARNING >>>
Detected Illegal Vacuum Level.
After the error is cleared, the check result list is displayed.
Please check the nozzle of NG as shown in the following content.
1. Plugged Nozzle
2. Plugged Head Shaft
3. Data of Vacuum Level
真空全部果
<<< 警告 >>>
出异常
解除后示果列表。
生前、 果 NG 的吸嘴的以下几点。
1. 吸嘴内部堵塞
2. 装内部堵塞
3. 数据的
Ea07544 SHAFT CLEANING BLOW ALL CHECK RESULT
<<< WARNING >>>
Detected Illegal Vacuum Level.
After the error is cleared, the check result list is displayed.
Please check the nozzle of NG as shown in the following content.
1. Plugged Nozzle
2. Plugged Head Shaft
3. Data of Vacuum Level
吸嘴排气全部果
<<< 警告 >>>
出异常。
解除后示果列表。
生前、 果 NG 的吸嘴的以下几点。
1. 吸嘴内部堵塞
2. 装内部堵塞
3. 数据的
Ea07545 SHAFT CLEANING BLOW ERROR
<<< WARNING >>>
Detected Illegal Vacuum Level.
TABLE
NOZZLE
HEAD
Investigate the following item.
1. Plugged Nozzle
2. Plugged Head Shaft
3. Data of Vacuum Level
吸嘴排气
<<< 警告 >>>
出异常。
工作台号
吸嘴
Head
确以下几点。
1. 吸嘴内部堵塞
2. 装内部堵塞
3. 数据的
Ea07546 "ALARM: BASE FAN IS ABNORMAL"
The Base FAN of Machine is not working.
When Machine is kept running, will be cause trouble of Machine.
Please consult your distributor for further information
with FAN number.
FAN number:
片机散扇异常
出了片机的扇异常。
运行、会引作。
下列号后、与制造厂商系。
扇号:
Ea07548 ALARM: BASE FAN IS ABNORMAL
The Base FAN of Printer is not working.
When Machine is kept running, will be cause trouble of Printer.
Please consult your distributor for further information
with FAN number.
FAN number:
印刷机排扇异常
出了印刷机的扇异常。
运行，会引作。
下列号，与制造厂商系。
扇号:
Ea07702 CAMERA LIGHT START ERROR
Camera light can't be started.
相机照明启
相机照明的启失了。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 110 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Please reboot the machine after clearing the error. 清除提示后，重新启机器。
Ea07800 SOME COMPONENTS ARE NOT POSSIBLE TO PICK UP
The OPT-FLAG prevents the machine to pick up next
component.
Mount data
Component data Name
Head
存在不可吸附的元件。
OPT-FLAG 出分割吸附、装的指示，
因此下列元件的吸附已被禁止。
装数据 号
元件数据 号 名称
装 号
Ea07801 SOME COMPONENTS ARE NOT POSSIBLE TO PICK UP
The head is already occupied by another component,
and the indicated picking action is not possible.
Mount data
Component data Name
Head
存在不可吸附的元件。
装已其他元件占有，不能行指定的吸附。
装数据 号
元件数据 号 名称
装 号
Ea07802 SOME COMPONENTS ARE NOT POSSIBLE TO PICK UP
A picking up group without rotation-action could not
include a mounting data with some rotation.
Mount data
Component data Name
Head
存在不可吸附的元件。
在不旋装的状下行吸附、装的中，
不能加入旋装行装的装数据。
装数据 号
元件数据 号 名称
装 号
Ea07803 SOME COMPONENT COULD NOT BE PICKED UP
By picking up this component, depending on the pick up
accuracy, the component could hit the component on
neighbor nozzle.
Mount data
Component data Name
Head
存在不可吸附的元件。
行吸附后，根据吸附位置的歪斜量，
已判定会与分配到相吸嘴的元件相碰。
装数据 号
元件数据 号 名称
装 号
Ea07804 SOME COMPONENT COULD NOT BE PICKED UP
By picking up this component, depending on the pick up
accuracy, the component could hit the neighbor nozzle
with component.
Mount data
Component data Name
Head
存在不可吸附的元件。
行吸附后，根据吸附位置的歪斜量，
已判定会与吸附着元件的相吸嘴相碰。
装数据 号
元件数据 号 名称
装 号
Ea07805 SOME COMPONENTS ARE NOT POSSIBLE TO PICK UP
A picking up group without rotation-action could not
include the FINE type component. Check the data.
Mount data
Component data Name
Head
存在不可吸附的元件。
在不旋装的状下行吸附、装的中
不能加入 FINE 型的元件。
确数据。
装数据 号
元件数据 号 名称
装 号
Ea07806 SOME COMPONENT COULD NOT BE PICKED UP
Because the machine had picked up a component of FINE type,
the machine could not pickup another of FINE type.
Mount data
Component data Name
Head
同一个吸附、装内，包含着数个 FINE 型元件。
必修改数据。
装数据 号
元件数据 号 名称
装 号
Ea07807 SOME COMPONENT COULD NOT BE PICKED UP
By picking up this component, depending on the pick up
accuracy, the component could hit the neighbor nozzle
without component.
Mount data
Component data Name
Head
存在不可吸附的元件。
行吸附后，根据吸附位置的歪斜量，已判定，
元件的一会与没有元件的相吸嘴相碰。
装数据 号
元件数据 号 名称
装 号
Ea07808 SOME COMPONENT COULD NOT BE PICKED UP
By picking up this component, depending on the pick up
accuracy, the component could hit the neighbor nozzle
without component during the rotating the component.
Mount data
Component data Name
Head
存在不可吸附的元件。
行吸附后，根据吸附位置的歪斜量，已判定，
旋元件，会与没有元件的相的吸嘴相碰。
装数据 号
元件数据 号 名称
装 号
Ea07809 SOME COMPONENT COULD NOT BE PICKED UP
The machine had tried to pickup components belongs
different blocks.
Mount data
Component data Name
Head
存在不可吸附的元件。
正要在同一吸附、装内跨越多个拼来吸附元件。
装数据 号
元件数据 号 名称
装 号
Ea07810 NO COMPONENT FOR USE
A component is not available at this moment.
Please confirm the component to be ready,
and run again.
Mount data
Component data Name
存在不可使用的元件。
因下列元件已判定元件用完或不可使用，
所以无法使用。
装数据 号
元件数据 号 名称
装 号