YAMAHA 报警资料 - 第229页

Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 229 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…

100%1 / 237
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 228 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
- All components were empty.
Close the door or supply components and run again.
Component data
Start Pallet No.
End Pallet No.
元件数据 号
料架始号󱓖 号
料架󱮨束号󱓖 号
Ea29085 Ext. tray changer Door opening error
Cannot use the following component because the door is open.
Please close the door and restart production.
Component data
Start Pallet No.
End Pallet No.
外部托󱎭交󰀷器 柜󳊽打󳇮󲣄
因柜󳊽敞着，所以下列元件不能使用。
󲣌在󳋂柜󳊽后，重新始运行。
元件数据 号
料架始号󱓖 号
料架󱮨束号󱓖 号
Ea29086 Auto tray changer Components empty
All the tray for the parts are not available.
This can be caused by the followings:
- All the tray is empty.
- Tray changer door is open.
Please supply parts or close the door and
start auto-running again.
Parts No. Name
Start Pallet No.
End Pallet No.
自托󱎭交󰀷器 元件用完󳇮󲣄
由柜󳊽敞或元件用完等原因，
不能使用下列元件。
󲣌󳋂柜󳊽或󲔺充元件后，重新始运行。
元件数据 号 名称
料架始号󱓖 [PLTcmp_inf4]号
料架󱮨束号󱓖 [PLTcmp_inf5]号
Ea29087 Ext. tray changer Component empty
Cannot use the following component because the component is empty.
Please supply the component and restart production.
Parts No. Name
Start Pallet No.
End Pallet No.
外部托󱎭交󰀷器 元件用完󳇮󲣄
因元件已用完，所以不能使用下列元件。
󲣌在󲔺充元件后，重新始运行。
元件数据 号 名称
料架始号󱓖 [PLTcmp_inf4]号
料架󱮨束号󱓖 [PLTcmp_inf5]号
Ea29088 Auto tray changer Confirmation of special dump back
A component will be dumped back to the tray.
If you already supply component in the tray changer,
Be sure to press "EMERGENCY STOP", remove the component from the head,
and run again.
Component data Name
自托󱎭交󰀷器 供󱮮装置作确󲡹
按照特殊返󲲭理的󲢓置，将元件返回到托󱎭。
因生托󱎭󲡶数停止󳇮󲣄，所以可能已󱮤向
托󱎭供󱮮装置󲔺充了元件。
如已󲔺充了元件󰋋，可能会造成元件的重叠放置，
所以󲣌按󱧼急停机按󳆃，将元件从 Head 上取出后，
再重新始运行。
元件数据 号 名称
Ea29089 Auto tray changer Component empty stop
Following tray component was used up.
Refill the component and push the indicator button.
Component Name Comment
Start Pallet No.
End Pallet No.
自托󱎭元件用完停机
以下托󱎭元件呈空的状。
󲣌󲔺充元件后、按指示器按󳆃。
元件名称 注
料架始号󱓖 号
料架󱮨束号󱓖 号
Ea29090 Ext. tray changer Component empty stop
Following tray component was used up.
Refill the component and push the indicator button.
Component Name Comment
Start Pallet No.
End Pallet No.
外部托󱎭元件用完停机
以下托󱎭元件呈空的状。
󲣌󲔺充元件后、按指示器按󳆃。
元件名称 注
料架始号󱓖 号
料架󱮨束号󱓖 号
Ea29100 Auto tray changer Pallet set error
Failed to start the Hook Action.
Please check the following items:
1. Set Pallet (No. ) correctly.
2. The hook nail is curved.
3. The sensor of hook is broken.
4. The magazine is put illegal position.
5. The door is open.
If the pallet is out of the magazine, then:
1. Be sure to press "EMERGENCY STOP".
2. Remove the pallet from the stage.
3. Return the pallet to its magazine.
自托󱎭交󰀷器 料架抽出󳇮󲣄
抓手未能正常作。
󲣌注意下列󳕎目。
1. 将料架 (No. )重新放入到正确的位置上
2. 抓手的爪弯曲了
3. 抓手感器的作不良
4. 收󱮈柜没有正常安装
5. 收󱮈的收󱮈柜柜󳊽敞着
料架从收󱮈柜抽出󰋋，󲣌按照如下󰠺󳝹󲲰行理。
1. 按󱧼急停机
2. 取出料架
3. 将料架放入收󱮈柜
Ea29101 Ext. tray changer Pallet set error
Failed to start the Hook Action.
Please check the following items:
1. Set Pallet (No. ) correctly.
2. The hook nail is curved.
3. The sensor of hook is broken.
4. The magazine is put illegal position.
5. The door is open.
If the pallet is out of the magazine, then:
1. Be sure to press "EMERGENCY STOP".
2. Remove the pallet from the stage.
3. Return the pallet to its magazine.
外部托󱎭交󰀷器 料架抽出󳇮󲣄
抓手未能正常作。
󲣌注意下列󳕎目。
1. 将料架 (No. )重新放入到正确的位置上
2. 抓手的爪弯曲了
3. 抓手感器的作不良
4. 收󱮈柜没有正常收󱮈
5. 收󱮈的收󱮈柜的柜󳊽敞着
料架从收󱮈柜抽出󰋋，󲣌按照如下󰠺󳝹󲲰行理。
1. 按󱧼急停机
2. 取出料架
3. 将料架放入收󱮈柜
Ea29102 Auto tray changer Hook action error
Failed to start the Hook Action.
自托󱎭交󰀷器 抓手作󳇮󲣄
抓手未能正常作。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 229 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Please check the following items:
1. The sensor of hook is broken.
2. The hook nail is curved.
If the pallet is out of the magazine, then:
1. Be sure to press "EMERGENCY STOP".
2. Remove the pallet from the stage.
3. Return the pallet to its magazine.
󲣌注意下列󳕎目。
1. 抓手感器的作不良
2. 抓手的爪弯曲了
料架从收󱮈柜抽出󰋋，󲣌按照如下󰠺󳝹󲲰行理。
1. 按󱧼急停机
2. 取出料架
3. 将料架放入收󱮈柜
Ea29103 Ext. tray changer Hook action error
Failed to start the Hook Action.
Please check the following items:
1. The sensor of hook is broken.
2. The hook nail is curved.
If the pallet is out of the magazine, then:
1. Be sure to press "EMERGENCY STOP".
2. Remove the pallet from the stage.
3. Return the pallet to its magazine.
外部托󱎭交󰀷器 抓手作󳇮󲣄
抓手未能正常作。
󲣌注意下列󳕎目。
1. 抓手感器的作不良
2. 抓手的爪弯曲了
料架从收󱮈柜抽出󰋋，󲣌按照如下󰠺󳝹󲲰行理。
1. 按󱧼急停机
2. 取出料架
3. 将料架放入收󱮈柜
Ea29104 Auto tray changer : Failed to pull out the pallet
Cannot set the designated pallet, because the Hook Pallet sensor doesn't detect
pallet.
Please check whether the designated pallet is set correctly.
And please check whether the Hook Pallet sensor does work correctly.
Stage No.
Pallet No.
Hook Pallet sensor:Undetect (ATS )
*To check current sensor status, see [Unit]-[Auto TC] or [I/O] view.
自托󱎭交󰀷器 料架抽出󳇮󲣄
因抓手的料架󰖕出感器没有感，所以不能
󲢓置指定的料架。
󲣌确󲡹是否正确󲢓置了指定的料架。
另外，󲣌确󲡹抓手的料架󰖕出感器是否正确感。
料架台号󱓖 号
料架号󱓖 号
抓手料架存在感器:未󰖕出 (ATS )
*当前的感器状,可在[装置]-[自托󱎭]或[I/O]画面确󲡹。
Ea29105 ATS hook action error
The hook doesn't move normally.
Please check whether something is detected on stage set position sensor.
自托󱎭交󰀷器 抓手作󳇮󲣄
抓手没有正常作
󲣌确󲡹料架台安装位置感器是否有什反。
Ea29106 Ext. tray changer Sensor mismatch
The Stage Set sensor detects it, but the axis movement is not possible
because the Pallet Exist sensor of the hook does not detect it.
Please confirm whether the pallet is correctly set.
Moreover, please confirm whether the Stage Set sensor and the Pallet Exist
sensor of the hook are correctly reactive.
Stage No.
*To check current sensor status, see [Unit]-[Ext. TC] or [I/O] view.
Ext. tray changer Sensor mismatch___
The Stage Set sensor detects it, but the axis movement is not possible
because the Pallet Exist sensor of the hook does not detect it.
Please confirm whether the pallet is correctly set.
Moreover, please confirm whether the Stage Set sensor and the Pallet Exist
sensor of the hook are correctly reactive.
Stage No.
*To check current sensor status, see [Unit]-[Ext. TC] or [I/O] view.
Ea29110 Auto tray changer Latch error
The pallet latch condition is illegal.
Please check the latch sensor and the tray changer.
Possible causes are as follows:
1.The pallet latch does not work correctly.
2.The open/close sensor of pallet latch does wrong reaction.
自托󱎭交󰀷器 󳊾󳇖状󳇮󲣄
󳊾󳇖未能正常作。
可能由如下原因所造成的。
󲣌确󲡹󳊾󳇖及托󱎭交󰀷器的状。
1. 󳊾󳇖没有正常作
2. 󳊾󳇖感器做出了󳇮󲣄的判断
Ea29111 Ext. tray changer Latch error
The pallet latch condition is illegal.
Please check the latch sensor and the tray changer.
Possible causes are as follows:
1.The pallet latch does not work correctly.
2.The open/close sensor of pallet latch does wrong reaction.
外部托󱎭交󰀷器 󳊾󳇖状󳇮󲣄
󳊾󳇖未能正常作。
可能由如下原因所造成的。
󲣌确󲡹󳊾󳇖及托󱎭交󰀷器的状。
1. 󳊾󳇖没有正常作
2. 󳊾󳇖感器做出了󳇮󲣄的判断
Ea29120 Auto tray changer Magazine clamp error
Can't work TrayChanger, because the magazine clamp is off.
Please open the door and lock the magazine clamp.
自托󱎭交󰀷器 收󱮈柜固󳇮󲣄
因没有安装收󱮈柜固定，所以托󱎭交󰀷器不能作。
󲣌打柜󳊽并确󲡹收󱮈柜固定的状。
Ea29121 Ext. tray changer Magazine clamp error
Can't work TrayChanger, because the magazine clamp is off.
Please open the door and lock the magazine clamp.
Stage No.
Magazine No.
外部托󱎭交󰀷器 收󱮈柜固󳇮󲣄
因没有安装收󱮈柜固定，所以托󱎭交󰀷器不能作。
󲣌打柜󳊽并确󲡹收󱮈柜固定的状。
料架台号󱓖 号
收󱮈柜号󱓖 号
Ea29122 Ext. tray changer Magazine clamp error
The magazine clamp is off.
Please open the door and lock the magazine clamp.
Stage No.
Magazine No.
外部托󱎭交󰀷器 收󱮈柜固󳇮󲣄
因没有安装收󱮈柜固定，󲣌安装收󱮈柜固定。
料架台号󱓖 号
收󱮈柜号󱓖 号
Ea29130 Auto tray changer : Pallet protrudes from magazine
The pallet is protruded from the magazine.
Please press the "EMERGENCY STOP"
and return the pallet to the magazine by hand.
Stage No.
Magazine No.
Pallet Origin sensor:Detect (ATS )
*To check current sensor status, see [Unit]-[Auto TC] or [I/O] view.
自托󱎭交󰀷器 料架出󳇮󲣄
料架从收󱮈柜中出。
󲣌按󱧼急停机按󳆃，并用手将料架放回到收󱮈柜。
工作台号󱓖 号
收󱮈柜号󱓖 号
料架出感器:󰖕出 (ATS )
*当前的感器状,可在[装置]-[自托󱎭]或[I/O]画面确󲡹。
Ea29131 Ext. tray changer Pallet protrude error
The pallet is out of the Ext.Tray magazine.
Please press the "EMERGENCY STOP"
外部托󱎭交󰀷器 料架出󳇮󲣄
料架从收󱮈柜中出。
󲣌按󱧼急停机按󳆃，并用手将料架放回到收󱮈柜。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 230 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
and return the pallet to the magazine by hand.
Stage No.
Magazine No.
料架台号󱓖 号
收󱮈柜号󱓖 号
Ea29132 Auto tray changer Rack protrude error
The magazine is protruded to the door direction.
Please check the Rack Origin sensor.
And please check whether the magazine is set correctly.
自托󱎭交󰀷器 󲱒料箱出󳇮󲣄
收󱮈柜正向柜󳊽方向出。
󲣌确󲡹󲱒料箱出感器的状。
另外，󲣌确󲡹收󱮈柜是否已正确󲢓置。
Ea29133 Auto tray changer Restarting error
Can not restart production because tray changer is dangerous or unexpected status.
If some pallets are out of the magazine, Please restore with the following procedure.
1. Press the "EMERGENCY STOP"
2. Remove the pallet by the hand
3. Press the ready button
4. Open the door and insert the pallet in original position
5. Close the door
自托󱎭交󰀷器 再次启󳇮󲣄
因托󱎭交󰀷器在危󳌾的状或没有󳕙料的状，所以不能再次启。
当料架从收󱮈柜中出󰋋，󲣌用如下󳕏序恢。
1. 按󱧼急停机按󳆃
2. 用手将料架取出
3. 按 Ready 按󳆃
4. 打柜󳊽，将料架放回到原来的位置
5. 󳋂柜󳊽
Ea29134 Auto tray changer : Failed to return the pallet
The pallet is protruded from the magazine.
Please press the "EMERGENCY STOP"
and return the pallet to the magazine by hand.
Stage No.
Magazine No.
Pallet Origin sensor:Detect (ATS )
*To check current sensor status, see [Unit]-[Auto TC] or [I/O] view.
自托󱎭交󰀷器 料架退回失󲧺
料架从收󱮈柜中出。
󲣌按󱧼急停机按󳆃，并用手将料架放回到收󱮈柜。
料架台号󱓖 号
收󱮈柜号󱓖 号
料架出感器:󰖕出 (ATS )
*当前的感器状,可在[装置]-[自托󱎭]或[I/O]画面确󲡹。
Ea29135 Auto tray changer : Failed to pull out the pallet
The pallet is protruded from the magazine.
Please press the "EMERGENCY STOP"
and return the pallet to the magazine by hand.
Stage No.
Magazine No.
Pallet Origin sensor:Detect (ATS )
*To check current sensor status, see [Unit]-[Auto TC] or [I/O] view.
自托󱎭交󰀷器 料架抽出失󲧺
料架从收󱮈柜中出。
󲣌按󱧼急停机按󳆃，并用手将料架放回到收󱮈柜。
料架台号󱓖 号
收󱮈柜号󱓖 号
料架出感器:󰖕出 (ATS )
*当前的感器状,可在[装置]-[自托󱎭]或[I/O]画面确󲡹。
Ea29136 Auto tray changer Restarting error
Can not restart production because tray changer is dangerous or unexpected status.
If some pallets are out of the magazine, Please restore with the following procedure.
1. Press the "EMERGENCY STOP"
2. Remove the pallet by the hand
3. Press the ready button
4. Open the door and insert the pallet in original position
5. Close the door
Stage No.
自托󱎭交󰀷器 料架退回󳇮󲣄
因托󱎭交󰀷器在危󳌾的状或没有󳕙料的状，所以不能再次启。
当料架从收󱮈柜中出󰋋，󲣌用如下󳕏序恢。
1. 按󱧼急停机按󳆃
2. 用手将料架取出
3. 按 Ready 按󳆃
4. 打柜󳊽，将料架放回到原来的位置
5. 󳋂柜󳊽
料架台号󱓖 号
Ea29137 Auto tray changer Restarting error
Can not restart production because tray changer is dangerous or unexpected status.
If some pallets are out of the magazine, Please restore with the following procedure.
1. Press the "EMERGENCY STOP"
2. Remove the pallet by the hand
3. Press the ready button
4. Open the door and insert the pallet in original position
5. Close the door
Stage No.
自托󱎭交󰀷器 料架抽出󳇮󲣄
因托󱎭交󰀷器在危󳌾的状或没有󳕙料的状，所以不能再次启。
当料架从收󱮈柜中出󰋋，󲣌用如下󳕏序恢。
1. 按󱧼急停机按󳆃
2. 用手将料架取出
3. 按 Ready 按󳆃
4. 打柜󳊽，将料架放回到原来的位置
5. 󳋂柜󳊽
料架台号󱓖 号
Ea29140 Auto tray changer Pallet set error
The pallet is on the stage.
Please put it into the magazine and execute it again.
自托󱎭交󰀷器 料架抽出󳇮󲣄
料架已抽出至料架台。
󲣌将料架放回到收󱮈柜，并再次行。
Ea29141 Ext. tray changer Pallet set error
The pallet is on the stage.
Please put it into the magazine and execute it again.
外部托󱎭交󰀷器 料架抽出󳇮󲣄
料架已抽出至料架台。
󲣌将料架退回到收󱮈柜，并再次行。
Ea29142 Auto tray changer : There is unknown pallet
Unknown pallet is detected by the sensor during pallet action.
Please return the pallet to the magazine.
Stage No.
Stage Set position sensor:Detect (ATS )
*To check current sensor status, see [Unit]-[Auto TC] or [I/O] view.
自托󱎭交󰀷器 存在不明料架
退回/抽出料架的作中，󰖕出了不明料架。
󲣌将已抽出至料架台的料架退回收󱮈柜。
料架台号󱓖 号
料架台安装位置感器 (ATS )
料架台中󳋉位置感器:某一个󰖕出 (ATS )
*当前的感器状,可在[装置]-[自托󱎭]或[I/O]画面确󲡹。
Ea29143 Ext. tray changer Pallet set error
Unknown pallet is detected by the sensor during pallet action.
Please return the pallet to the magazine.
Stage set sensor: Detect
外部托󱎭交󰀷器 料架抽出󳇮󲣄
退回/抽出料架的作中，󰖕出了不明的料架。
󲣌将已抽出至料架台上的料架退回收󱮈柜。
料架台安装位置感器 󰖕出料架
Ea29144 Auto tray changer : Pallet was lost
A pallet is lost by the sensor during pallet action.
Please check the pallet doesn't exist on the stage.
Stage No.
Stage Set position sensor:Undetect (ATS )
*To check current sensor status, see [Unit]-[Auto TC] or [I/O] view.
自托󱎭交󰀷器 料架迷失
退回/抽出料架的作中，未能󰖕出料架台上的料架。
如料架已出收󱮈柜，󲣌将料架退回收󱮈柜。
料架台号󱓖 号
料架台安装位置感器:未󰖕出 (ATS )
*当前的感器状,可在[装置]-[自托󱎭]或[I/O]画面确󲡹。