YAMAHA 报警资料 - 第230页

Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 230 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…

100%1 / 237
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 229 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Please check the following items:
1. The sensor of hook is broken.
2. The hook nail is curved.
If the pallet is out of the magazine, then:
1. Be sure to press "EMERGENCY STOP".
2. Remove the pallet from the stage.
3. Return the pallet to its magazine.
󲣌注意下列󳕎目。
1. 抓手感器的作不良
2. 抓手的爪弯曲了
料架从收󱮈柜抽出󰋋，󲣌按照如下󰠺󳝹󲲰行理。
1. 按󱧼急停机
2. 取出料架
3. 将料架放入收󱮈柜
Ea29103 Ext. tray changer Hook action error
Failed to start the Hook Action.
Please check the following items:
1. The sensor of hook is broken.
2. The hook nail is curved.
If the pallet is out of the magazine, then:
1. Be sure to press "EMERGENCY STOP".
2. Remove the pallet from the stage.
3. Return the pallet to its magazine.
外部托󱎭交󰀷器 抓手作󳇮󲣄
抓手未能正常作。
󲣌注意下列󳕎目。
1. 抓手感器的作不良
2. 抓手的爪弯曲了
料架从收󱮈柜抽出󰋋，󲣌按照如下󰠺󳝹󲲰行理。
1. 按󱧼急停机
2. 取出料架
3. 将料架放入收󱮈柜
Ea29104 Auto tray changer : Failed to pull out the pallet
Cannot set the designated pallet, because the Hook Pallet sensor doesn't detect
pallet.
Please check whether the designated pallet is set correctly.
And please check whether the Hook Pallet sensor does work correctly.
Stage No.
Pallet No.
Hook Pallet sensor:Undetect (ATS )
*To check current sensor status, see [Unit]-[Auto TC] or [I/O] view.
自托󱎭交󰀷器 料架抽出󳇮󲣄
因抓手的料架󰖕出感器没有感，所以不能
󲢓置指定的料架。
󲣌确󲡹是否正确󲢓置了指定的料架。
另外，󲣌确󲡹抓手的料架󰖕出感器是否正确感。
料架台号󱓖 号
料架号󱓖 号
抓手料架存在感器:未󰖕出 (ATS )
*当前的感器状,可在[装置]-[自托󱎭]或[I/O]画面确󲡹。
Ea29105 ATS hook action error
The hook doesn't move normally.
Please check whether something is detected on stage set position sensor.
自托󱎭交󰀷器 抓手作󳇮󲣄
抓手没有正常作
󲣌确󲡹料架台安装位置感器是否有什反。
Ea29106 Ext. tray changer Sensor mismatch
The Stage Set sensor detects it, but the axis movement is not possible
because the Pallet Exist sensor of the hook does not detect it.
Please confirm whether the pallet is correctly set.
Moreover, please confirm whether the Stage Set sensor and the Pallet Exist
sensor of the hook are correctly reactive.
Stage No.
*To check current sensor status, see [Unit]-[Ext. TC] or [I/O] view.
Ext. tray changer Sensor mismatch___
The Stage Set sensor detects it, but the axis movement is not possible
because the Pallet Exist sensor of the hook does not detect it.
Please confirm whether the pallet is correctly set.
Moreover, please confirm whether the Stage Set sensor and the Pallet Exist
sensor of the hook are correctly reactive.
Stage No.
*To check current sensor status, see [Unit]-[Ext. TC] or [I/O] view.
Ea29110 Auto tray changer Latch error
The pallet latch condition is illegal.
Please check the latch sensor and the tray changer.
Possible causes are as follows:
1.The pallet latch does not work correctly.
2.The open/close sensor of pallet latch does wrong reaction.
自托󱎭交󰀷器 󳊾󳇖状󳇮󲣄
󳊾󳇖未能正常作。
可能由如下原因所造成的。
󲣌确󲡹󳊾󳇖及托󱎭交󰀷器的状。
1. 󳊾󳇖没有正常作
2. 󳊾󳇖感器做出了󳇮󲣄的判断
Ea29111 Ext. tray changer Latch error
The pallet latch condition is illegal.
Please check the latch sensor and the tray changer.
Possible causes are as follows:
1.The pallet latch does not work correctly.
2.The open/close sensor of pallet latch does wrong reaction.
外部托󱎭交󰀷器 󳊾󳇖状󳇮󲣄
󳊾󳇖未能正常作。
可能由如下原因所造成的。
󲣌确󲡹󳊾󳇖及托󱎭交󰀷器的状。
1. 󳊾󳇖没有正常作
2. 󳊾󳇖感器做出了󳇮󲣄的判断
Ea29120 Auto tray changer Magazine clamp error
Can't work TrayChanger, because the magazine clamp is off.
Please open the door and lock the magazine clamp.
自托󱎭交󰀷器 收󱮈柜固󳇮󲣄
因没有安装收󱮈柜固定，所以托󱎭交󰀷器不能作。
󲣌打柜󳊽并确󲡹收󱮈柜固定的状。
Ea29121 Ext. tray changer Magazine clamp error
Can't work TrayChanger, because the magazine clamp is off.
Please open the door and lock the magazine clamp.
Stage No.
Magazine No.
外部托󱎭交󰀷器 收󱮈柜固󳇮󲣄
因没有安装收󱮈柜固定，所以托󱎭交󰀷器不能作。
󲣌打柜󳊽并确󲡹收󱮈柜固定的状。
料架台号󱓖 号
收󱮈柜号󱓖 号
Ea29122 Ext. tray changer Magazine clamp error
The magazine clamp is off.
Please open the door and lock the magazine clamp.
Stage No.
Magazine No.
外部托󱎭交󰀷器 收󱮈柜固󳇮󲣄
因没有安装收󱮈柜固定，󲣌安装收󱮈柜固定。
料架台号󱓖 号
收󱮈柜号󱓖 号
Ea29130 Auto tray changer : Pallet protrudes from magazine
The pallet is protruded from the magazine.
Please press the "EMERGENCY STOP"
and return the pallet to the magazine by hand.
Stage No.
Magazine No.
Pallet Origin sensor:Detect (ATS )
*To check current sensor status, see [Unit]-[Auto TC] or [I/O] view.
自托󱎭交󰀷器 料架出󳇮󲣄
料架从收󱮈柜中出。
󲣌按󱧼急停机按󳆃，并用手将料架放回到收󱮈柜。
工作台号󱓖 号
收󱮈柜号󱓖 号
料架出感器:󰖕出 (ATS )
*当前的感器状,可在[装置]-[自托󱎭]或[I/O]画面确󲡹。
Ea29131 Ext. tray changer Pallet protrude error
The pallet is out of the Ext.Tray magazine.
Please press the "EMERGENCY STOP"
外部托󱎭交󰀷器 料架出󳇮󲣄
料架从收󱮈柜中出。
󲣌按󱧼急停机按󳆃，并用手将料架放回到收󱮈柜。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 230 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
and return the pallet to the magazine by hand.
Stage No.
Magazine No.
料架台号󱓖 号
收󱮈柜号󱓖 号
Ea29132 Auto tray changer Rack protrude error
The magazine is protruded to the door direction.
Please check the Rack Origin sensor.
And please check whether the magazine is set correctly.
自托󱎭交󰀷器 󲱒料箱出󳇮󲣄
收󱮈柜正向柜󳊽方向出。
󲣌确󲡹󲱒料箱出感器的状。
另外，󲣌确󲡹收󱮈柜是否已正确󲢓置。
Ea29133 Auto tray changer Restarting error
Can not restart production because tray changer is dangerous or unexpected status.
If some pallets are out of the magazine, Please restore with the following procedure.
1. Press the "EMERGENCY STOP"
2. Remove the pallet by the hand
3. Press the ready button
4. Open the door and insert the pallet in original position
5. Close the door
自托󱎭交󰀷器 再次启󳇮󲣄
因托󱎭交󰀷器在危󳌾的状或没有󳕙料的状，所以不能再次启。
当料架从收󱮈柜中出󰋋，󲣌用如下󳕏序恢。
1. 按󱧼急停机按󳆃
2. 用手将料架取出
3. 按 Ready 按󳆃
4. 打柜󳊽，将料架放回到原来的位置
5. 󳋂柜󳊽
Ea29134 Auto tray changer : Failed to return the pallet
The pallet is protruded from the magazine.
Please press the "EMERGENCY STOP"
and return the pallet to the magazine by hand.
Stage No.
Magazine No.
Pallet Origin sensor:Detect (ATS )
*To check current sensor status, see [Unit]-[Auto TC] or [I/O] view.
自托󱎭交󰀷器 料架退回失󲧺
料架从收󱮈柜中出。
󲣌按󱧼急停机按󳆃，并用手将料架放回到收󱮈柜。
料架台号󱓖 号
收󱮈柜号󱓖 号
料架出感器:󰖕出 (ATS )
*当前的感器状,可在[装置]-[自托󱎭]或[I/O]画面确󲡹。
Ea29135 Auto tray changer : Failed to pull out the pallet
The pallet is protruded from the magazine.
Please press the "EMERGENCY STOP"
and return the pallet to the magazine by hand.
Stage No.
Magazine No.
Pallet Origin sensor:Detect (ATS )
*To check current sensor status, see [Unit]-[Auto TC] or [I/O] view.
自托󱎭交󰀷器 料架抽出失󲧺
料架从收󱮈柜中出。
󲣌按󱧼急停机按󳆃，并用手将料架放回到收󱮈柜。
料架台号󱓖 号
收󱮈柜号󱓖 号
料架出感器:󰖕出 (ATS )
*当前的感器状,可在[装置]-[自托󱎭]或[I/O]画面确󲡹。
Ea29136 Auto tray changer Restarting error
Can not restart production because tray changer is dangerous or unexpected status.
If some pallets are out of the magazine, Please restore with the following procedure.
1. Press the "EMERGENCY STOP"
2. Remove the pallet by the hand
3. Press the ready button
4. Open the door and insert the pallet in original position
5. Close the door
Stage No.
自托󱎭交󰀷器 料架退回󳇮󲣄
因托󱎭交󰀷器在危󳌾的状或没有󳕙料的状，所以不能再次启。
当料架从收󱮈柜中出󰋋，󲣌用如下󳕏序恢。
1. 按󱧼急停机按󳆃
2. 用手将料架取出
3. 按 Ready 按󳆃
4. 打柜󳊽，将料架放回到原来的位置
5. 󳋂柜󳊽
料架台号󱓖 号
Ea29137 Auto tray changer Restarting error
Can not restart production because tray changer is dangerous or unexpected status.
If some pallets are out of the magazine, Please restore with the following procedure.
1. Press the "EMERGENCY STOP"
2. Remove the pallet by the hand
3. Press the ready button
4. Open the door and insert the pallet in original position
5. Close the door
Stage No.
自托󱎭交󰀷器 料架抽出󳇮󲣄
因托󱎭交󰀷器在危󳌾的状或没有󳕙料的状，所以不能再次启。
当料架从收󱮈柜中出󰋋，󲣌用如下󳕏序恢。
1. 按󱧼急停机按󳆃
2. 用手将料架取出
3. 按 Ready 按󳆃
4. 打柜󳊽，将料架放回到原来的位置
5. 󳋂柜󳊽
料架台号󱓖 号
Ea29140 Auto tray changer Pallet set error
The pallet is on the stage.
Please put it into the magazine and execute it again.
自托󱎭交󰀷器 料架抽出󳇮󲣄
料架已抽出至料架台。
󲣌将料架放回到收󱮈柜，并再次行。
Ea29141 Ext. tray changer Pallet set error
The pallet is on the stage.
Please put it into the magazine and execute it again.
外部托󱎭交󰀷器 料架抽出󳇮󲣄
料架已抽出至料架台。
󲣌将料架退回到收󱮈柜，并再次行。
Ea29142 Auto tray changer : There is unknown pallet
Unknown pallet is detected by the sensor during pallet action.
Please return the pallet to the magazine.
Stage No.
Stage Set position sensor:Detect (ATS )
*To check current sensor status, see [Unit]-[Auto TC] or [I/O] view.
自托󱎭交󰀷器 存在不明料架
退回/抽出料架的作中，󰖕出了不明料架。
󲣌将已抽出至料架台的料架退回收󱮈柜。
料架台号󱓖 号
料架台安装位置感器 (ATS )
料架台中󳋉位置感器:某一个󰖕出 (ATS )
*当前的感器状,可在[装置]-[自托󱎭]或[I/O]画面确󲡹。
Ea29143 Ext. tray changer Pallet set error
Unknown pallet is detected by the sensor during pallet action.
Please return the pallet to the magazine.
Stage set sensor: Detect
外部托󱎭交󰀷器 料架抽出󳇮󲣄
退回/抽出料架的作中，󰖕出了不明的料架。
󲣌将已抽出至料架台上的料架退回收󱮈柜。
料架台安装位置感器 󰖕出料架
Ea29144 Auto tray changer : Pallet was lost
A pallet is lost by the sensor during pallet action.
Please check the pallet doesn't exist on the stage.
Stage No.
Stage Set position sensor:Undetect (ATS )
*To check current sensor status, see [Unit]-[Auto TC] or [I/O] view.
自托󱎭交󰀷器 料架迷失
退回/抽出料架的作中，未能󰖕出料架台上的料架。
如料架已出收󱮈柜，󲣌将料架退回收󱮈柜。
料架台号󱓖 号
料架台安装位置感器:未󰖕出 (ATS )
*当前的感器状,可在[装置]-[自托󱎭]或[I/O]画面确󲡹。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 231 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Ea29145 Ext. tray changer Pallet set error
A pallet is lost by the sensor during pallet action.
Please check the pallet doesn't exist on the stage.
Stage set sensor: Undetect
外部托󱎭交󰀷器 料架抽出󳇮󲣄
退回/抽出料架的作中，没有󰖕出本存在的料架。
󲣌确󲡹料架是否已抽出至料架台。
料架台安装感器 未󰖕出料架
Ea29146 Ext. tray changer Axis moving error
Stage(DZ axis) can't move, because Hook axis(DY axis) is near the magazine.
On the [Unit]-[Ext. TC]-[Axis] screen, please keep away the hook axis (DY axis)
from the magazine.
Stage No.
Ext. tray changer Axis moving error___
Stage(DZ axis) can't move, because Hook axis(DY axis) is near the magazine.
On the [Unit]-[Ext. TC]-[Axis] screen, please keep away the hook axis (DY axis)
from the magazine.
Stage No.
Ea29147 Auto tray changer : Failed to return the pallet
When returning pallet,
unknown pallet was detected on stage.
Please return the pallet on stage to magazine.
Stage No.
Stage Set position sensor (ATS )
Stage Middle position sensor:Either Detect (ATS )
*To check current sensor status, see [Unit]-[Auto TC] or [I/O] view.
自托󱎭交󰀷器 料架退回失󲧺
退回料架的途中，在料架台上󰖕出了不明料架。
󲣌将料架台上的料架退回收󱮈柜。
料架台号󱓖 号
料架台安装位置感器 (ATS )
料架台中󳋉位置感器: 󰖕出任意一个 (ATS )
*当前的感器状,可在[装置]-[自托󱎭]或[I/O]画面确󲡹。
Ea29148 Auto tray changer : Failed to pull out the pallet
When pull out pallet,
pallet was not detected on stage.
If pallet is protruding from magazine, please return it to magazine.
Stage No.
Stage Set position sensor:Undetect (ATS )
*To check current sensor status, see [Unit]-[Auto TC] or [I/O] view.
自托󱎭交󰀷器 料架抽出失󲧺
抽出料架的途中，未能在料架台上󰖕出料架。
如料架已出收󱮈柜󰋋，󲣌将料架退回收󱮈柜。
料架台号󱓖 号
料架台安装位置感器:未󰖕出 (ATS )
*当前的感器状,可在[装置]-[自托󱎭]或[I/O]画面确󲡹。
Ea29149 Ext. tray changer Axis moving error
Stage(DZ axis) can't move, because the pulled pallet is near the magazine.
On the [Unit]-[Ext. TC]-[Axis] screen, please keep away the hook axis (DY axis)
from the magazine.
Stage No.
Ext. tray changer Axis moving error___
Stage(DZ axis) can't move, because the pulled pallet is near the magazine.
On the [Unit]-[Ext. TC]-[Axis] screen, please keep away the hook axis (DY axis)
from the magazine.
Stage No.
Ea29150 Auto Tray changer Door opening error
The door is open.
Please close the door.
自托󱎭交󰀷器 柜󳊽打󳇮󲣄
柜󳊽敞着。
󲣌将敞的柜󳊽󳋂。
Ea29151 Ext. Tray changer Door opening error
The door is open.
Please close the door.
外部托󱎭交󰀷器 柜󳊽打󳇮󲣄
柜󳊽敞着。
󲣌将敞的柜󳊽󳋂。
Ea29152 Auto Tray changer Door opening error
The door is open or the door is not correctly closed.
Please close the door.
(When the door light is off in spite of the door switch 'close',
please turn the door switch into 'open' once and turn it 'close'.)
自托󱎭交󰀷器 柜󳊽打󳇮󲣄
柜󳊽敞着或没有好。
󲣌将敞的柜󳊽󳋂。
(当柜󳊽[󳋂]，但柜󳊽指示灯却灯󰋋，
󲣌先将柜󳊽置[]，然后再置[]。)
Ea29153 Ext. Tray changer Door opening error
The door is open or the door is not correctly closed.
Please close the door.
(When the door light is off in spite of the door switch 'close',
please turn the door switch into 'open' once and turn it 'close'.)
Stage No.
外部托󱎭交󰀷器 柜󳊽打󳇮󲣄
柜󳊽敞着或没有好。
󲣌将敞的柜󳊽󳋂。
(当柜󳊽[󳋂]，但柜󳊽指示灯却灯󰋋，
󲣌先将柜󳊽置[]，然后再置[]。)
料架台号󱓖 号
Ea29154 Auto tray changer Door opening error
Failed to servo-on because Auto tray changer door is open.
Please close the opening door and press the 'READY' button again.
自托󱎭交󰀷器 柜󳊽打󳇮󲣄
因自托󱎭交󰀷器的柜󳊽敞着，所以不能将伺服 ON。
将敞的柜󳊽󳋂后，󲣌再按一次'READY'按󳆃。
Ea29155 Ext. tray changer Door opening error
Failed to servo-on because Ext. tray changer door is open.
Please close the opening door and press the 'READY' button again.
外部托󱎭交󰀷器 柜󳊽打󳇮󲣄
因自托󱎭交󰀷器的柜󳊽敞着，所以不能将伺服 ON。
将敞的柜󳊽󳋂后，󲣌再按一次'READY'按󳆃。
Ea29156 Auto tray changer Door opening error
The operation of opening the door was interrupted by "EMERGENCY STOP".
There is a possibility that the position of the pallet is not correct.
After releasing the "EMERGENCY STOP", Please open the door again and return the
pallet.
(If the door switch is already 'open',
please turn the door switch into 'close' once and turn it 'open')
自托󱎭交󰀷器 柜󳊽打󳇮󲣄
因󱧼急停机理柜󳊽打作中断了。
料架可能不在正确的位置上。
󲣌按󱧼急停机按󳆃，然后重新打柜󳊽并装入料架。
(柜󳊽已''󰋋，󲣌先将柜󳊽置[]，
然后再置[]。)
Ea29157 Auto tray changer Door opening error
Can not start production because the operation of opening the door is not
completed.
Though door switch is 'Open', the pallet has not been returned yet.
This error is caused by interruptions of opening the door by emergency stop, etc.
Please put the pallet back in the magazine by opening the door again,
and restart the production.
自托󱎭交󰀷器 柜󳊽打󳇮󲣄
因柜󳊽打作没有完成，所以不能始自运行。
柜󳊽󲍒[]，但本退回的料架却抽出状。
󲢺状生于因󱧼急停机而引起的柜󳊽打中断等。
󲣌重新打柜󳊽并退回料架，再重新始自运行。
Ea29158 Auto tray changer Door opening warning
It may not move to the pallet drawer position,
because the door switch was operated quickly.
Please turn the door switch into 'close' once (the door light lights),
and turn it 'open' again.
自托󱎭交󰀷器 柜󳊽打󳇮󲣄
由于󲲜快操作柜󳊽，所以可能󲲭未移到
可󲲰行抽出的位置。
󲣌先将柜󳊽置[]，等柜󳊽指示灯点亮
后，再置[]。
Ea29159 Auto tray changer Magazine set warning 自托󱎭交󰀷器 收󱮈柜安装警告