YAMAHA 报警资料 - 第233页
Comparison Table ( English - Chinese ) VGOS V2.46STD R1.000 233 / 237 Copyright (C) 2009 Y amaha Motor Co.,Ltd. All Rights Reserved. Code Code Code Code Englis h Englis h Englis h Englis h Chinese Chinese Chinese Chinese…
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 232 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
The magazine is not set correctly.
Please check the following points.
1. The magazine clamp must be locked correctly.
2. The pallet suppression of the magazine must be tightened correctly.
3. The pallet not protruding from the magazine.
收柜料箱的安装不正确。
确如下几点。
1. 收柜固定必定
2. 收柜的料架具必定
3. 料架没有从收柜中出
Ea29160 Auto tray changer Door closing warning
The door was closed with the door switch 'close'.
In this state, the tray changer can not work.
Please turn the door switch into 'open', and turn it 'close' again.
自托交器 柜警告
在柜位置[]的状下了柜。
状下，托交器可能无法作。
先将柜置[]，再置[]。
Ea29161 Auto tray changer Door opening error
Can not open the door because of the INTERLOCK error.
Please turn the door switch 'open' and remove the cause of the INTERLOCK error.
Then please turn the door switch 'close' once again.
自托交器 柜打
因正在中，所以不能打柜。
先将柜置[]，等排除原因后，
再置[]。
Ea29162 Ext. tray changer Door opening warning
It may not move to the pallet drawer position,
because the door switch was operated quickly.
Please turn the door switch into 'close' once (the door light lights),
and turn it 'open' again.
外部托交器 柜打
由于快操作柜，所以可能未移到
可行抽出的位置。
先将柜置[]，等柜指示灯点亮
后，再置[]。
Ea29163 Ext. tray changer Magazine set warning
The magazine is set, but the magazine clamp is not locked correctly.
Please open the door and lock the magazine clamp.
外部托交器 收柜安装警告
然安装了收柜，但没有定收柜固定。
定收柜固定。
Ea29164 Ext. tray changer Door closing warning
The door was closed with the door switch 'close'.
In this state, the tray changer can not work.
Please turn the door switch into 'open', and turn it 'close' again.
外部托交器 柜警告
在柜位置[]的状下了柜。
状下，托交器可能无法作。
先将柜置[]，再置[]。
Ea29165 Ext. tray changer Door opening error
The door switch is 'open'.
Please turn the door switch 'close'.
(When the door is open,
turn the door switch 'close' after closing the door first, please)
Stage No.
外部托交器 柜打
柜位置[]。
将柜置[]。
(柜敞，先将柜，然后置[]。)
料架台号 号
Ea29180 Auto tray changer Picking error
Cannot pick a component from the tray.
If components are empty, please supply components.
When there are components,
please check whether a component can be picked from a tray correctly.
If there is a head vacuuming a component, remove it and restart production.
Mount data
Component data Name
Start Pallet No.
End Pallet No.
自托交器 吸附
未能从托吸附元件。
元件用完，充元件。
存在元件，确是否能从托正确吸附元件。
如正吸附着元件，在取出后再次运行。
装数据 号
元件数据 号 名称
料架始号 号
料架束号 号
Ea29181 Ext. tray changer Picking error
Cannot pick a component from the tray.
If tray components are empty, please supply components.
When there are tray components,
please check whether a component can be picked from a tray correctly.
If there is a head vacuuming a component, remove it and restart production.
Mount data
Component data Name
Start Pallet No.
End Pallet No.
Tray Head No.
外部托交器 吸附
未能从托吸附元件。
元件用完，充元件。
存在元件，确是否能从托正确吸附元件。
如正吸附着元件，在取出后再次运行。
装数据 号
元件数据 号 名称
料架始号 号
料架束号 号
Head 号 号
Ea29182 Ext. tray changer Component supply error
Failed to put the component on the station.
There is a possibility that the component was dropped around the station.
Please remove the component and restart production.
Mount data
Component data Name
Station
Next tray position is for the next pick sequence.
(X= , Y= )
外部托交器 元件供
未能将元件正确放在料站上。
元件可能掉落在料站或其周。
取出元件后重新运行。
装数据 号
元件数据 号 名称
料站 号
接下来要使用的元件在托上的位置：
(X= 号, Y= 号)
Ea29183 Ext. tray changer Component supply error
The component is not placed correctly on the station.
If the component is on the station, please remove it.
Mount data
Component data Name
Station
Next tray position is for the next pick sequence.
(X= , Y= )
外部托交器 元件供
供元件没有正确放置在料站上。
的料站上存在元件，取出。
装数据 号
元件数据 号 名称
料站 号
接下来要使用的元件在托上的位置：
(X= 号, Y= 号)
Ea29184 Ext. tray changer Component supply error
Unknown component is on the station.
Please remove the component and restart production.
外部托交器 元件供
料站上放着元件。
在取出元件后再次运行。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 233 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
Mount data
Component data Name
Station
装数据 号
元件数据 号 名称
料站 号
Ea29185 Ext. Tray changer Reset error
The tray changer head or traverser station
has a component attached to its nozzle (pad).
Please remove the component.
外部托交器 初始化
外部托的 Head 或料站上存在元件。
取出。
Ea29186 Ext. tray changer Component supply error
Failed in component supply from the head of traverser to the station.
There is a possibility
that the component was dropped around the transfer course or the station.
Please remove the component and restart production.
Mount data
Component data Name
Head number
外部托交器 元件供
从送小 Head 向站点的料失了。
元件可能掉落在料途中或站点周。
在取出元件后再次运行。
装数据 号
元件数据 号 名称
Head 号 号
Ea29187 Ext. tray changer Component supply error
Failed in component supply from the head of traverser to the station.
There is a possibility
that the component was dropped around the transfer course or the station.
Please remove the component and restart production.
Mount data
Component data Name
Head number
外部托交器 元件供
从送小 Head 向站点的料失了。
元件可能掉落在料途中或站点周。
在取出元件后再次运行。
装数据 号
元件数据 号 名称
Head 号 号
Ea29188 Ext. tray changer Component supply error
When parts were mounted, ExtTray detected the error.
There is a possibility of taking components home to the station.
If there are components on the station,
please remove the component and restart production.
Station No.
外部托交器 元件回
装元件，在外部托交器上生了元件回。
当料站上存在元件，在取出后再次运行。
料站号 号
Ea29189 Ext. tray changer Axis moving error
Traverser(DX axis) cannot move, because station(DS axis) is dangerous position.
Possible causes are as follows. Please check whether the axes are safe.
1. The head unit and the station interfere
2. The safety sensor of Station is illegal
外部托交器 移
因站点(DS )在危的位置上，所以送小(DX )不能移。
原因如下。确是否在安全的位置。
1. Head 装置和站点相互干。
2. 站点下降端感器异常。
Ea29190 Ext. tray changer Axis moving error
Station(DS axis) cannot move, because Traverser(DX axis) is dangerous position.
Possible causes are as follows. Please check whether the axes are safe.
1. The head unit and the station interfere
2. The safety sensor of Traverser is illegal
外部托交器 移
因送小(DX )在危的位置上，所以不能移站点(DS )。
原因如下。确是否在安全的位置。
1. Head 装置和站点相互干。
2. 送小安全感器异常。
Ea29191 Auto tray changer Picking error
Cannot pick a component from the tray. If tray components are empty,
please supply components. When there are tray components,
please check whether a component can be picked from a tray correctly.
If there is a head vacuuming a component, remove it and restart production.
Component data Name
Error Pallet
Next tray position is as follows.
Pallet No.
(X= , Y= )
自托交器 吸附
未能从托吸附元件。
元件用完，充元件。
存在元件，确是否能从托正确吸附元件。
如正吸附着元件，在取出后再次运行。
元件数据 号 名称
料架号 号
下一个使用元件的位置:
料架号 号
(X= 号, Y= 号)
Ea29192 Ext. tray changer Picking error
Cannot pick a component from the tray. If tray components are empty,
please supply components. When there are tray components,
please check whether a component can be picked from a tray correctly.
If there is a head vacuuming a component, remove it and restart production.
Component data Name
Error Pallet
Tray Head No.
Next tray position is as follows.
Pallet No.
(X= , Y= )
外部托交器 吸附
未能从托吸附元件。
元件用完，充元件。
存在元件，确是否能从托正确吸附元件。
如正吸附着元件，在取出后再次运行。
元件数据 号 名称
料架号 号
托 Head 号 号
下一个使用元件的位置:
料架号 号
(X= 号, Y= 号)
Ea29193 Ext. Tray changer Reset error
The head of ext. tray changer is vacuuming a component.
Please remove the component and retry again.
外部托交器 位
外部托交器的 Head 正吸附着元件。
在取出元件后，再次运行。
Ea29194 Ext. Tray changer Reset error
The station of ext. tray changer is vacuuming a component.
Please remove the component and retry again.
外部托交器 位
外部托交器的站点上放着元件。
在取出元件后，再次运行。
Ea29195 Ext. tray changer Cannot vacuum component
Ext. tray head is vacuuming component. Remove it by hand.
Failed to vacuum component, because vacuum level of head is already high.
Head No.
外部托交器 不能吸附元件
外部托 Head 吸附着元件，用手取下。
因 Head 的真空上升，没能吸附元件。
Head 号 号
Ea29196 Auto tray changer Pallet mismatch
The pulled Pallet No. that pick up parts is different from
自托交器 料架不一致
吸附元件所抽出的料架号，与元件信息中的当前料架号不一致。
Comparison Table ( English - Chinese )
VGOS V2.46STD R1.000 234 / 237 Copyright (C) 2009 Yamaha Motor Co.,Ltd. All Rights Reserved.
Code
CodeCode
Code
English
EnglishEnglish
English
Chinese
ChineseChinese
Chinese
the Current Pallet No. of the parts information.
Please reset, and restart at the Halfway Continue.
Mount No.
Head No.
Parts No.
Pulled Pallet No.
Parts Current Pallet No.
Parts Start Pallet No.
Parts End Pallet No.
行位后，用从中途始运行命令重新始运行。
装号
Head 号
元件号
抽出的料架号
元件信息中的当前料架号
元件信息中的始料架号
元件信息中的束料架号
Ea29200 Auto Tray changer Reset abort error
Aborted the RESET process.
When a pallet is out of the magazine, please remove it
and return it to its assigned magazine by hand.
自托交器 位中断
位理已中止。
如料架出了料架台，用手将其退回收柜中。
Ea29201 Ext. Tray changer Reset abort error
Aborted the RESET process.
When a pallet is out of the magazine, please remove it
and return it to its assigned magazine by hand.
外部托交器 位中断
位理已中止。
如料架出了料架台，用手将其退回收柜中。
Ea29202 Ext. Tray changer Reset error
Because the station of ext. tray changer is vacuuming a component,
a component that the head is vacuuming cannot supply to the station.
Please remove the component and retry again.
外部托交器 位
外部托交器的料站上有元件，
所以 Head 没能将吸附着的元件交料站。
去除元件后，重新行。
Ea29203 Ext. tray changer Reset error
Failed to put the component on the station.
There is a possibility that the component was dropped around the station.
Please remove the component and retry again.
外部托交器 位
没能在料站上正确放置元件。
料站及其周可能有落下的元件存在。
去除元件后，重新行。
Ea29204 Ext. tray changer Reset error
Failed in component supply from the head of traverser to the station.
There is a possibility
that the component was dropped around the transfer course or the station.
Please remove the component and retry again.
外部托交器 位
从送小向料站交接元件失了。
送路上或料站周可能有落下的元件存在。
去除元件后，重新行。
Ea29210 Auto tray changer Timeout error
The head and Tray changer could not shake hand.
Please inform follows No to the maker.
Error Detail
ATS CTRL No.
自托交器 超
主机想要从托吸附元件，但无法与托取得一致，所以超了。
用下列号向制造厂商咨。
号 号
ATS CTRL 号 号
Ea29211 Auto tray changer Pallet status error
The reaction of the stage sensor is abnormal.
Please confirm the state of the sensor and the pallet.
自托交器 料架状
料架台安装感器的反异常。
确感器和料架的状。
Ea29212 Ext. tray changer Head action error
Failed to start the ExtTray Head Action.
Please check the following items:
1. The sensor of Ext.Tray head is broken.
2. Part thickness on a pallet.
3. Tray thickness on a pallet.
外部托交器 Head 作
外部托的 Head 未能正常作。
注意下列目。
1. Head 上升、下降端感器作不良
2. 料架上的元件厚度
3. 料架上的托厚度
Ea29220 ILLEGAL BOARD DETECTION ON BUFFER CONVEYOR
During conveyance from the check position to the exit position
by the buffer conveyor,
the Board was simultaneously detected on the following sensors.
the check position sensor and the exit position sensor
When the board is in both the check position sensor
and the exit position sensor of the buffer conveyor,
please take out Either the board.
冲送装置出了异常基板
在冲送装置，从位置向出口位置送的程中，
下列感器同出了基板。
位置感器和出口位置感器
冲送装置的位置感器和出口位置感器上
同存在基板，取出其中之一。
Ea29221 ILLEGAL BOARD DETECTION ON BUFFER CONVEYOR
During check and conveyance from the check position to the exit position
by the buffer conveyor, the Board was detected on the following sensor.
the entrance position sensor.
When the board is in both the check position sensor
and the entrance position sensor of the buffer conveyor,
please take out the board on the entrance position.
冲送装置出了异常基板
在冲送装置行或从位置向出口送的程中，
下列感器出了基板。
入口位置感器
冲送装置的位置感器和入口位置感器上
同存在基板，取出入口的基板。
Ea29222 BUFFER CONVEYOR TRANSFER TIMEOUT ERROR
The following Board became the transfer error.
The transfer Board from the entrance position to the check position
Get rid of the following causes thought about,
and please move forward the Board to the next transport position.
- The Board has fallen from the conveyor.
- The Board is caught on the way.
- The conveyor belt is not turning.
- The sensor has not detected the board.
Move forward the Board to [ check position ]
冲送装置送超
下列基板生了送。
从入口位置 向 位置 送的基板
可能是因下列原因所致，采取措施后将基板放置在送目的位置。
·基板从送上掉下来了。
·基板被卡在途中。
·送的皮没有。
·感器没有感到基板。
将基板送至[位置]。
Ea29223 BUFFER CONVEYOR TRANSFER TIMEOUT ERROR
The following Board became the transfer error.
The transfer Board from the check position to the exit position
冲送装置送超
下列基板生了送。
从位置 向 出口位置 送的基板