00196378-0102_UM X-Feeder_EN - 第23页

Overview of X Feeder Modules Display at the Tape Feeder Modules Functions and Operating Controls User Manual X Feeder M odules SIPLACE Family 23 Ad 1.: Pitch display The currently set pitch is indic ated at the operator …

Overview of X Feeder Modules

Functions and Operating Controls Display at the Tape Feeder Modules

22 User Manual X Feeder Modules SIPLACE Family

3.1.2 Display at the Tape Feeder Modules

3.1.2.1 LED Display on the 2x8 mm Tape Feeder Modules

Status display

▪ If the status display lights up green, the respective track of the feeder module is ready-to-operate

and needed for the current placement job. This status display also lights up green, if no placement

job has been assigned yet.

▪ If the status display is orange, this indicates that a warning has been issued.

▪ If the status display lights up red, an error has occurred. In the case, the pitch display indicates the

error source.

▪ If the status display remains dark, the feeder module is not needed for the current placement job.

Definitions of Terms Describing the Operating and Display Functions

Operator panel of the 2x8 mm tape feeder modules

Legend

1. Pitch display (LEDs) right

2. Track display right

3. Track change button

4. Forwards button

5. Backwards button

6. Foil button

7. Set button

8. Status display (2x)

9. Track display left

10. Pitch display (LEDs) left

The X feeder modules are equipped with 10 LEDs

(1, 2, 9 and 10) for indicating the operating states and

one multi-colored status display for each track (8).

Display The display indicates a specific status (e. g. the currently set pitch or the se-

lected track) and consists of several LEDs.

LED Abbreviation for "light emitting diode". LED designates a single element in a

display (e. g. left track "L").

Short press of the button The button is pressed and released within 0.75 seconds.

Long press of the button The button is being pressed more than 0.75 seconds.

Fast flashing

The LED is on and off for 0.15 second each, i. e., it flashes 3.3 times per

second.

Slow flashing

The LED is on and off for 0.45 second each, i. e., it flashes approx. once per

second.

Running light forwards The LEDs 1, 2, 4 and 8 of the pitch display light up one after another and

then they are all off. After that this sequence is repeated.

Running light backwards The LEDs 8, 4, 2 and 1 of the pitch display light up one after another and

then they are all off. After that this sequence is repeated.

Overview of X Feeder Modules

Display at the Tape Feeder Modules Functions and Operating Controls

User Manual X Feeder Modules SIPLACE Family 23

Ad 1.: Pitch display

The currently set pitch is indicated at the operator panel for both tracks by the corresponding LED 1, 2,

4 or 8.

Ad 2.: Track display

Indicates the relevant active track, that is triggered by the operating buttons. There is a left (L) and a

right (R) track.

Ad 3.: TRACK CHANGE button

Short press: When the TRACK CHANGE button is released, the track display switches to the

other track. The following button inputs will trigger this track until the TRACK

CHANGE button will be pressed again.

The 2x8 mm X feeder module consists of two individual 8 mm tracks. Both tracks

are controlled via the operator panel, although only one track can be active at any

one time. The other buttons, FORWARDS; BACKWARDS; FOIL and SET, always refer

to the currently active track.

Ad 4.: FORWARDS button

Short press: When the button is released, a tape transport cycle in forward direction is started

using the currently set pitch.

Long press: a) The foil is not tensioned: The tape drive continuously transports forwards as

long as the button remains pressed.

b) The foil is tensioned: The tape is repeatedly transported forwards as long

as the button remains pressed.

Ad 5.: BACKWARDS button

Short press: When the button is released, a tape transport cycle in backward direction is started

using the currently set pitch.

Long press: a) The foil is not tensioned: The tape drive continuously transports backwards as

long as the button remains pressed and the foil rocker

does not move down.

b) The foil is tensioned: The tear down procedure is enabled.

c) Torn foil error active: The tear down procedure is performed immediately.

Caution: If you pace the feeder module backwards, lift the pickup window from the cover foil by pushing

it up or by using the locking latch. Otherwise, the cover foil will be damaged.

Ad 6.: FOIL button

By pressing this button the foil removal motor is started.

It is moving until one of the following events occurs:

▪ the button was released

▪ the button was pressed longer than 30 sec. and the foil is not tensioned yet

The foil tension made the rocker move down to the switch off point.

Ad 7.: SET button

Together with the FORWARDS, BACKWARDS or FOIL button the SET button serves for setting the

pitch and the pickup position.

Ad 8.: STATUS display

Indicates the current status of both tracks.

Overview of X Feeder Modules

Functions and Operating Controls Display at the Tape Feeder Modules

24 User Manual X Feeder Modules SIPLACE Family

Error Messages

Basically, three types of errors can be distinguished for 2x8 mm tape feeder modules:

▪ Track errors: These are displayed, if an error occurs in the drives or the sensors of the feeder module

that is only relevant for the respective track of the feeder module.

▪ Process errors: These are sent to the feeder module by the placement machine and are displayed

by the feeder module.

▪ Module errors: These are displayed, if an error occurs in the control unit of the feeder module that

concerns the whole feeder module.

The feeder module always indicates an error state by a red status display. Either one or both LEDs can

light up red in this case.

The status of the pitch display allows for a distinction of the error type.

For module and track errors one or more slowly flashing LEDs of the pitch display give additional infor-

mation about the error type (see below).

Display of a track error

NOTICE

Art und Quelle der Gefahr

If one of the buttons (except the Track change button) is pressed, while a module or track

error is signalled, the currently set pitch is temporarily displayed for the selected track or both

tracks (in case of module errors). The status display still lights up red.

One second after releasing the button, the pitch display switches back to the error mode.

One LED of the pitch display in the track at fault flashes

slowly.

The pitch display signals the error type:

▪ LED 8: - Feed error

▪ LED 4 - (not in use)

▪ LED 2 - Torn foil

▪ LED 1 - Foil removal error

At least one LED of the status display lights up red.

NOTICE! Track errors can occur in both tracks

at the same time (right-hand picture).

Within one track two errors at most can occur. In this

case, two LEDs of the pitch display for this track are

flashing.