00196378-0102_UM X-Feeder_EN - 第27页

Overview of X Feeder Modules Display at the Tape Feeder Modules Functions and Operating Controls User Manual X Feeder M odules SIPLACE Family 27 Error Messages Display text LED display Meaning Troubleshooting None red, f…

Overview of X Feeder Modules

Functions and Operating Controls Display at the Tape Feeder Modules

26 User Manual X Feeder Modules SIPLACE Family

3.1.2.2 LCD and Status Display on 8 - 88 mm Tape Feeder Modules

Status display

▪ If the status display lights up green, the feeder module is ready-to-operate and is needed for the

current placement job. This status display also lights up green, if no placement job has been

assigned yet.

▪ If the status display is orange, this indicates that a warning has been issued. The message is shown

at the LCD:

▪ If the status display lights up red, a malfunction has occurred. The error message is shown at the

LCD:

▪ If the feeder module is not included in the current setup, the status display will remain dark.

Error Messages

The following tables give an overview of the different messages, their meaning and the measures that

have to be taken for fixing the error.

▪ The status display lights up orange in case of warnings and red in case of error messages. At the

same time a message is shown at the LCD of the operator panel.

Warnings

Operator panel

Legend

1. LCD

2. "Forwards" button (green)

3. "Backwards" button (green)

4. "Foil" button (yellow)

5. "Set" button (white)

6. Status display, multicolored (red / orange / green)

These feeder modules are equipped with a multicolored

status display (6) for signalling the operating states and

with a LCD for displaying the messages (1).

Display text LED display Meaning Troubleshooting

Remove Foil

orange The selected function is not

permitted when the cover foil

is tensioned (foil rocker is

pressed down).

If you want to perform this func-

tion, remove the foil from the pair

of toothed wheels and cut it, to re-

lax the foil rocker.

Overview of X Feeder Modules

Display at the Tape Feeder Modules Functions and Operating Controls

User Manual X Feeder Modules SIPLACE Family 27

Error Messages

Display text LED display Meaning Troubleshooting

None red, flashing The application software is

not present or faulty. Soft-

ware remains in the boot

loader.

Load the application software.

Handle

red The feeder module has been

logged in but the removal

handle has not yet been

pushed into the feeder mod-

ule.

Push the removal handle into the

feeder module.

Low Voltage

(Undervoltage)

orange 24 V supply voltage has not

increased the switching on

threshold after being

switched on.

Check the power supply.

Low Voltage

(Undervoltage)

red 24 V supply voltage has al-

ready exceeded the switch-

ing on threshold and has then

collapsed.

Check the power supply.

Feed Timeout

TransTimeout

(Timeout in tape

feeder cycle)

red Tape feeder cycle did not end

correctly within the specified

time (timeout for the "Feed"

function).

Is the tape reel jammed in the

container?

Is the component trapped in the

pickup area, between the tape

and the component window?

Eliminate the obstacle and restart

the conveyor using the arrow

keys of the operator panel. The

feeder module will finish the faulty

feed run and will return to its cor-

rect position.

Foil Torn

red Cover foil was not tensioned

within the prescribed time.

Probably, the foil has been torn.

Re-insert the cover foil and ten-

sion it.

Foil PeelErr

(Error when peeling

off the foil)

red Cover foil has not been cor-

rectly stripped off, although

the tape is being fed in.

The cover foil has probably been

trapped under the pickup window

and therefore has not been

stripped off properly.

Foil Jam

red The foil removal motor is

blocked.

Check, if the foil disposal rolls are

blocked by the cover foil.

EEP-WriteErr

(Error while backing

up data in the EEP-

ROM)

red The data backup has not

been performed correctly in

the EEPROM.

Since the position of the drive is

stored in the EEPROM, a refer-

ence run is necessary in these

cases. Acknowledge the error by

pressing the grey button at the

operator panel. After that, press

the yellow button to acknowledge

the prompt for a reference run

(see the reference run issue for

details).

EEP-ReadErr

(Error while reading

the EEPROM)

red The data from the EEPROM

have not been correctly read.

EEP-DataErr

(Error while backing

up the data in the

EEPROM)

red The data backup has not

been performed completely

in the EEPROM.

Overview of X Feeder Modules

Functions and Operating Controls Energy and Data Transfer

28 User Manual X Feeder Modules SIPLACE Family