00196378-0102_UM X-Feeder_EN - 第63页
Operating Tape Feeder Modules Adjusting the Pickup Positions Using the Operator Panel User Manual X Feeder M odules SIPLACE Family 63 4.3.1.2 Overview of the Operator Panel for 8 - 88 mm Feeder Modu les Colors of the sta…
Operating Tape Feeder Modules
Using the Operator Panel Overview of the Operator Panels
62 User Manual X Feeder Modules SIPLACE Family
4.3 Using the Operator Panel
4.3.1 Overview of the Operator Panels
4.3.1.1 Overview of the Operator Panel for 2x8 mm Feeder Modules
Colors of the status display
The status display uses different colors to indicate the current state of the feeder module.
1. LED 8 mm pitch left track
2. LED 4 mm pitch left track
3. LED 2 mm pitch left track
4. LED 1 mm pitch left track
5. LED L left track active
6. Track change button
7. Forwards button
8. Backwards button
9. Foil button
10. Set button
11. LED 8 mm pitch right track
12. LED 4 mm pitch right track
13. LED 2 mm pitch right track
14. LED 1 mm pitch right track
15. LED R right track active
16. Status display left track
17. Status display right track
Display Meaning
Is off The feeder is not in use.
Lights up green The feeder module is used and ready-to-operate.
* The feeder module is set up with the correct components.
Lights up red Error
The feeder module was deactivated by the station.
Lights up orange Usually indicates a warning (see also "5.1 Messages for 2x8 mm Feeder Mod-
ules" [ ➙ 79])
* The feeder module immediately needs more components.
* This information is only displayed if the line is equipped with a SIPLACE setup verification software.
Operating Tape Feeder Modules
Adjusting the Pickup Positions Using the Operator Panel
User Manual X Feeder Modules SIPLACE Family 63
4.3.1.2 Overview of the Operator Panel for 8 - 88 mm Feeder Modules
Colors of the status display
The status display uses different colors to indicate the current state of the feeder module.
4.3.2 Adjusting the Pickup Positions
You adjust the pickup position of an X feeder module using the operator panel at its rear end.
4.3.2.1 Pick-Up Positions for 2x8 mm Feeder Modules
Three different pickup positions can be set for 2x8 mm feeder modules.
The 2x8 mm X feeder module has three pickup positions. These are marked on the pickup window by
three lines level with the sprocket wheel.
Legend
1. Display
2. Backwards button (green)
3. Forwards button (green)
4. Foil button (yellow)
5. Set button (white)
6. Status display
Display Meaning
Is off The feeder is not in use.
Lights up green The feeder module is used and ready-to-operate
(* and set-up with the correct components).
Lights up red Error - The feeder module was deactivated by the station.
Lights up orange Usually indicates a warning (see also "5.2 Messages for 8 - 88 mm Feeder Mod-
ules" [ ➙ 84])
* The feeder module immediately needs more components.
* Is only displayed if the line is equipped with a SIPLACE setup verification software.
Pickup positions for 2x8 mm X feeder modules
Legend
1. Removal edge
2. Pickup position
3. Direction of tape movement
4. Pickup window
5. 2nd removal edge for CSPs (Chip Scaled Package)
This removal edge ensures that the components do
not keep sticking.
W: Component width
Operating Tape Feeder Modules
Using the Operator Panel Adjusting the Pickup Positions
64 User Manual X Feeder Modules SIPLACE Family
The pickup position to be adjusted depends on the component width W:
▪ Pickup position 1: W <= 0.5 mm
▪ Pickup position 2: 0.5 mm < W <= 1.5 mm
▪ Pickup position 3: 1.5 mm < W <= 3.5 mm
The set pickup position can be changed as follows:
NOTICE
When adjusting the pickup position the pitch display is used to represent the different positions.
The positions are assigned as follows:
►Pickup position 1 - LED 1
►Pickup position 2 - LED 2
NOTICE
Before the adjustment it may be necessary to select the desired track using the Track change
button.
►(1) Initial status: To change the pickup position of the
selected track the Set button is pressed first. This
button must be pressed during the whole adjustment
process.
►(2) Activating the adjustment function: In addition to
the Set button the Foil button is briefly pressed and
released. As a consequence the pitch display of the
selected track indicates the currently set pickup posi-
tion by flashing fast.
►(3) Changing the pickup position: As long as the Set
button is pressed, the pickup position can be
changed by briefly pressing the Forwards or Back-
wards button. The pitch display of the selected track
indicates the changed pickup position by flashing
fast.
►Completing the adjustment: If the desired pickup posi-
tion is set the SET button must be released. The
feeder module saves the modification and the sprock-
et wheel is moved to the selected position.
NOTICE
When a pickup position has been set, the feeder module automatically sets a pitch in which
most components with the dimensions defined for this pickup position are packed. Thus, an ad-
ditional adjustment of the pitch is necessary in rare cases only.
When the adjustment is completed, the feeder module will automatically change the position of
the sprocket wheel, if the pickup position has changed.
Pickup position and pitch are assigned as follows:
►Pickup position 1 - 2 mm pitch
►Pickup position 2 - 4 mm pitch
NOTICE
8 mm pitch
The 8 mm pitch must be adjusted manually later on, if the machine does not specifies this pitch.