00196378-0102_UM X-Feeder_EN - 第65页

Operating Tape Feeder Modules Adjusting the Pickup Positions Using the Operator Panel User Manual X Feeder M odules SIPLACE Family 65 Pickup Position for 8 mm Pitch When using tapes with an 8 mm component pitch, a compon…

Operating Tape Feeder Modules

Using the Operator Panel Adjusting the Pickup Positions

64 User Manual X Feeder Modules SIPLACE Family

The pickup position to be adjusted depends on the component width W:

▪ Pickup position 1: W <= 0.5 mm

▪ Pickup position 2: 0.5 mm < W <= 1.5 mm

▪ Pickup position 3: 1.5 mm < W <= 3.5 mm

The set pickup position can be changed as follows:

NOTICE

When adjusting the pickup position the pitch display is used to represent the different positions.

The positions are assigned as follows:

►Pickup position 1 - LED 1

►Pickup position 2 - LED 2

NOTICE

Before the adjustment it may be necessary to select the desired track using the Track change

button.

►(1) Initial status: To change the pickup position of the

selected track the Set button is pressed first. This

button must be pressed during the whole adjustment

process.

►(2) Activating the adjustment function: In addition to

the Set button the Foil button is briefly pressed and

released. As a consequence the pitch display of the

selected track indicates the currently set pickup posi-

tion by flashing fast.

►(3) Changing the pickup position: As long as the Set

button is pressed, the pickup position can be

changed by briefly pressing the Forwards or Back-

wards button. The pitch display of the selected track

indicates the changed pickup position by flashing

fast.

►Completing the adjustment: If the desired pickup posi-

tion is set the SET button must be released. The

feeder module saves the modification and the sprock-

et wheel is moved to the selected position.

NOTICE

When a pickup position has been set, the feeder module automatically sets a pitch in which

most components with the dimensions defined for this pickup position are packed. Thus, an ad-

ditional adjustment of the pitch is necessary in rare cases only.

When the adjustment is completed, the feeder module will automatically change the position of

the sprocket wheel, if the pickup position has changed.

Pickup position and pitch are assigned as follows:

►Pickup position 1 - 2 mm pitch

►Pickup position 2 - 4 mm pitch

NOTICE

8 mm pitch

The 8 mm pitch must be adjusted manually later on, if the machine does not specifies this pitch.

Operating Tape Feeder Modules

Adjusting the Pickup Positions Using the Operator Panel

User Manual X Feeder Modules SIPLACE Family 65

Pickup Position for 8 mm Pitch

When using tapes with an 8 mm component pitch, a component offset of 4 mm with respect to the pickup

position may occur after threading in the tape.

It is possible to correct this offset without changing the set 8 mm pitch and without re-threading the tape,

using the following function:

CAUTION

The adjustment is automatically cancelled, if the feeder module receives a request or conveyor

command from the machine or if the Set button is being pressed more than 30 seconds.

In these cases any modification made is cancelled and the previously set pickup position is re-

tained.

NOTICE

Before the adjustment it may be necessary to select the desired track using the Track change

button.

►(1) Initial status: To correct the pickup position of the

selected track by 4 mm, the press Set button first.

This button must be pressed during the whole adjust-

ment process.

►(2) Activating the adjustment function: In addition to

the Set button press the Forwards button; both but-

tons must be pressed simultaneously for at least 0.75

seconds. After this time LED 4 on the pitch display of

the selected track starts to flash slowly. At the same

time the tape is moved forwards in this track by 4 mm.

The Forwards button can now be released.

►(3) Changing the tape position: As long as the Set

button is pressed, you can move the tape forwards by

another 4 mm in the selected track, if necessary, by

briefly pressing the Forwards button. LED 4 on the

pitch display continues to flash slowly.

►Completing the adjustment: If the tape has reached its

desired position, the release Set button. The pitch

display shows the 8 mm pitch set for the selected

track.

CAUTION

The adjustment is automatically cancelled, if the feeder module receives a request or conveyor

command from the machine or if the Set button is being pressed more than 30 seconds.

Operating Tape Feeder Modules

Using the Operator Panel Adjusting the Pickup Positions

66 User Manual X Feeder Modules SIPLACE Family

4.3.2.2 Pick-Up Positions for 8 mm X Feeder Modules

Four different pickup positions can be set for 8 mm X feeder modules.

Pickup positions for 8 mm X feeder modules

Legend

▪ Pickup position 1: (pitch 2 mm)

here, components with a width of (W) ≤ 0.5 mm are picked, e. g. 0201, 0402

▪ Pickup position 2: (pitch 4 mm)

here, components with a width of (W) > 0.5 mm and ≤ 1.5 mm are picked, e. g. 0603, 0805,

Micro-, Mini-Melf

▪ Pickup position 3: (pitch 4 mm)

here, components with a width of (W) > 1.5 mm and ≤ 3.5 mm are picked, e. g. 1206, SOT23

▪ Pickup position 4: (pitch 8 mm)

here, components with a width of (W) > 3.5 mm are picked.

A Direction of tape movement W Width of the components

B Foil removal edge 1-4 Numbers of the pickup positions