00196378-0102_UM X-Feeder_EN - 第88页

Messages Messages for 8 - 88 mm Feeder Modules Messages Sent by the Feede r Module 88 User Manual X Feeder Modules SIPLACE Family 5.2.1.21 Download Boot 5.2.1.22 Update Boot 5.2.1.23 New Parameters 5.2.1.24 EEPROM Read E…

Messages

Messages Sent by the Feeder Module Messages for 8 - 88 mm Feeder Modules

User Manual X Feeder Modules SIPLACE Family 87

5.2.1.16 Foil Jam

5.2.1.17 Remove the Foil

5.2.1.18 CAN Bus Error

5.2.1.19 Boot Error

5.2.1.20 Data Flash Error

LCD, de:

LCD, en:

Folienstau

Foil Jam

Status display: red

Cause: The foil motor is blocked because the foil disposal rolls are unable to move easily.

They are probably being blocked by the trapped foil

Solution: Remove the foil, empty the foil container and clean the foil disposal rolls.

LCD, de:

LCD, en:

Folie entf.

Remove Foil

Status display: orange

Cause: You have selected a function which is invalid while the cover foil is tensioned. The

foil rocker has been pushed down.

Solution: If you want to perform this function, remove the foil from the pair of toothed wheels

and cut it, to relax the foil rocker.

LCD, de:

LCD, en:

CANBusFehler

CANBusError

Status display: Red

Cause: CAN bus error, the feeder module is unable to communicate with the machine

(FCU).

Solution: Log out and on again, check the fibre optic cable interface.

If a reset does not help, please send the feeder module to ASM Assembly

Systems.

Comments: Clean the fibre optic cable interface

The fibre optic cable is a transparent plastic cable for transmitting light

Note: Include the component table in your error search!

LCD, de:

LCD, en:

BootFlashErr

Status display: red

Cause: Unable to correctly write data in boot or application memory.

Solution: Repeat the download of the boot software.

If the error persists: Download the application software first and then the boot soft-

ware.

If the error persists: Replace the control board of the feeder module.

Comments: This error will only appear during of after a boot software download.

LCD, de:

LCD, en:

DataFlashErr

Status display: red

Cause: Unable to write data in the data memory

Solution: Log the feeder module out and on.

If the error persists: Replace the control board of the feeder module.

Comments: The display text may also be FlashDataErr.

Messages

Messages for 8 - 88 mm Feeder Modules Messages Sent by the Feeder Module

88 User Manual X Feeder Modules SIPLACE Family

5.2.1.21 Download Boot

5.2.1.22 Update Boot

5.2.1.23 New Parameters

5.2.1.24 EEPROM Read Error

5.2.1.25 EEPROM Write Error

LCD, de:

LCD, en:

DownloadBoot

Status display: red

Cause: Data are being written from the data memory into the cache memory.

Solution: Wait

LCD, de:

LCD, en:

Update Boot

Status display: red

Cause: Data are being written from the cache memory into the boot memory.

Solution: Wait

LCD, de:

LCD, en:

ParameterNeu

New Default

Status display: orange

Cause: The feeder module software is automatically setting default parameters. This is

performed, for example, after loading new software and takes approx. 5 seconds.

Solution: Wait

LCD, de:

LCD, en:

EEP-ReadErr

Status display: red

Cause: Data was not read from the EEPROM correctly

Solution: Remove the tape. Acknowledge the error with the SET button. Then acknowledge

the request to perform a reference run with the yellow button. If this message con-

tinues to appear, you will need to replace the control board or the drive.

Comments: Since the position of the drive is stored in the EEPROM, a reference run is

necessary in these cases.

LCD, de:

LCD, en:

EEP-WriteErr

Status display: red

Cause: Data backup has not been performed correctly in the EEPROM.

Solution: Remove the tape. Acknowledge the error with the SET button. Then acknowledge

the request to perform a reference run with the yellow button. If this message con-

tinues to appear, you will need to replace the control board or the drive.

Comments: Since the position of the drive is stored in the EEPROM, a reference run is

necessary in these cases.

Messages

Messages From Process Messages for 8 - 88 mm Feeder Modules

User Manual X Feeder Modules SIPLACE Family 89

5.2.1.26 EEPROM Data Error

5.2.1.27 Scan Request

5.2.2 Messages From Process

5.2.2.1 Introduction

The following messages are only shown by the feeder module. The display text itself is generated by the

station computer and is then transmitted via the CAN bus to the LCD display of the feeder module. The

error source is therefore not in the feeder module but usually in the placement machine state. For exam-

ple, pickup or Vision errors, which affect the component of a particular track, will be displayed on the

feeder module for that track. The following table shows the LCD display text, the color and mode of the

status display, the cause and troubleshooting measures.

5.2.2.2 Not Verified

5.2.2.3 Scan Barcode

LCD, de:

LCD, en:

EEP-DataErr

Status display: red

Cause: The data back-up in the EEPROM was not carried out completely

Solution: Remove the tape. Acknowledge the error with the SET button. Acknowledge the

prompt for a reference run with the yellow button.

If the message continues to appear, you will need to replace the control board or

the drive.

Comments: Since the position of the drive is stored in the EEPROM, a reference run is

necessary in these cases.

LCD, de:

LCD, en:

Scan Anford.

Scan Request

Status display: - - -

Cause: The request to perform scanning has been sent by the feeder module to the MC

(Machine Controller).

Solution: - - -

Comments: After the grey SET button has been pressed (1 sec.) the display shows the

Scan Anford. / Scan Request message for approx. 2 sec. to indicate that

the feeder module has sent a request for barcode scanning to the MC. If a barcode

system is active, the MC will then send the Scan Barcode display text to the

feeder module.

From version 1.24

LCD, de:

LCD, en:

NichtGeprueft

Not verified

Status display:

Cause: The tape has been inserted but the barcode has not yet been scanned.

Solution: Scan the barcode.

Comments: This message is only shown if a barcode system has been installed and is active.

LCD, de:

LCD, en:

Scan Barcode

Status display:

Cause: The barcode still needs to be scanned.

Solution: Scan the barcode.

Comments: - - -