00193368-02 - 第53页

SIPLACE GEM for S25HM, S27HM, HS50, HS60 SW Version GEM 503.02 HOST Inter fac e Manual ©Siemens AG, all rights reser ved page 53 of 243 3.11 Remote Commands Setup and process ing on the SIPLACE m achines c an be driven b…

SIPLACE GEM for S25HM, S27HM, HS50 , HS60 SW Version GEM 503.02

HOST Interface Manual

Purge Spool

The SIPLACE is purging its spool, erasing all

spooled messages.

Transmit Spool

The SIPLACE is transmitting spooled messages

to the Host.

3.10.4 Related Variables

The following table lists the variables (SV's, EC's, or DVVALS) which are relevant to

spooling. For a more complete description of these variables, see "Appendix A --

Variables".

Variable Name VID

MAXSPOOLTRANSMIT 1002037

CONFIGSPOOL 1002045

SPOOLCOUNTACTUAL 1002038

SPOOLCOUNTTOTAL 1002039

OVERWRITESPOOL 1002046

SPOOLFULLTIME 1002040

SPOOLLOADSUBSTATE 1002041

SPOOLSTARTTIME 1002042

SPOOLSTATE 1002043

SPOOLUNLOADSUBSTATE 1002044

MAX_TIME_TO_STOP 1002942

SAFE_SPOOL_MODE 1002943

3.10.5 Related Events

The following lists the collection events (CEIDs) which are relevant to spooling. For a

more complete description of these events, see "Appendix B -- Collection Events" or the

description in this chapter.

Collection Event CEID

GemSpoolingActivated 1000007

GemSpoolingDeactivated 1000008

GemSpoolTransmitFailure 1000009

FM_GEM_SPOOL_FULL 2211039

SIPLACE GEM for S25HM, S27HM, HS50, HS60 SW Version GEM 503.02

HOST Interface Manual

3.11 Remote Commands

Setup and processing on the SIPLACE machines can be driven by either a local operator

or by a Host computer. This section describes the remote commands available at the

Host.

Much of the behavior of SIPLACE and its acceptance of remote commands is directed by

requirements of the Control State. For a complete description of the Control State, please

see section 3.2, "Control States".

The SIPLACE will accept remote commands only when the Control State is Remote.

While in the Local state, the Host can not put the Equipment into Remote, this must be

done by an operator at the Equipment.

The Host has the ability to configure whether the Equipment will enter the Remote or local

state as a default upon entering the On-Line state from Off-Line. This is done by setting

The ONLINESUBSTATE Equipment Constant (VID 1002009) to 4 (Local) or 5 (Remote).

Once in the Remote state, the Host has the authority to issue any of these remote

commands and they will not be rejected because of an invalid control state. Commands

may be rejected for other reasons (trying to start a process with no material loaded, etc.).

While in Remote state, the Operator still has the ability to issue commands and change

the control state. If the operator issues a command while in Remote state, the SIPLACE

will send the OPERATORCMDINREMOTESTATE collection event if enabled (CEID

1002056). When the Operator "grabs" control away from the Host by changing the

Control State to local, the SIPLACE will send either the GemControlStateLOCAL (CEID

1000003) or GemEquipmentOFFLINE (CEID 1000005) event to the Host.

3.11.1 S2F41 Commands

The general format for remote commands using the S2F41 message is:

S2F41 [W] * H->E

<L [2]

<A RCMD> * Remote command string

<L [2]

<A CPNAME> * Command Parameter Name

<CPVAL> * Command Parameter Value

...

> .

The following commands may be sent by the Host to the SIPLACE.

3.11.1.1 START

This command starts processing on the SIPLACE assuming all proper initialization has

taken place and material is present.

A Remote Start could conflict with a Safe_Spool_Stop until spooldata ist purged or

transmitted, , see "chapter 3.10 Spooling".

SIPLACE GEM for S25HM, S27HM, HS50 , HS60 SW Version GEM 503.02

HOST Interface Manual

S2F41 [W]

<L [2]

<L>

> .

3.11.1.2 STOP

This command will stop the processing of material at the Equipment. PCB´s currently in

process will be completed, but no new PCB will be loaded.

S2F41 [W]

<L [2]

<L>

> .