00193368-02 - 第66页

SIPLACE GEM for S25HM, S27HM, HS50 , HS60 SW Version GEM 503.02 HOST Inter fac e Manual Page 66 of 243 ©Siemens AG, all rights reser ved used in: S6F6 HCA CK - Host Com m and Param eter Ac k nowledge Code Format: B[1] 0 …

100%1 / 243
SIPLACE GEM for S25HM, S27HM, HS50, HS60 SW Version GEM 503.02
HOST Interface Manual
©Siemens AG, all rights reserved page 65 of 243
64 S_G_44_S
65 S_G_56_S
66 72mm-S tape
79 3x8 mm tape
80 8mm Surftape feeder
81 12mm Surftape feeder
82 24mm Surftape feeder
149 8mm tape „long“ 8mm
150 8mm "Schulz" tape
151 Fimecore
152 Nitto
153 Bulk-Case feeder
used in: PICKUPINFOREVx
FiducialName - Identifier of a fiduvial
Format: U2
used in: FIDUCIALDATA
Filling_level - Number of components in a division of a matrix tray changer
Format: I4
used in: MTCInfo
FillingLevel - unused always 0
Format U4
used in: TAPE_INFO
ForceIndex - programmed placement force
see chapter 3.5 in the SIPLACE Data Interface for a detailed description.
Format: U1
used in: PLACEINFOREVx
GANTRYGROUPID – ID of the gantry-group
Format: U2
1 = First gantrygroup in direction of transport
2 = Second gantrygroup in direction of transport
GANTRYID – ID of the gantry
Format: U2
1...4 (see charpter 'Machine Areas')
GRANT6 - Permission to send
Format: B[1]
0 = Permission granted
1 = Busy, try again
2 = Not interested
>2 = Other errors
3 - 63 reserved
SIPLACE GEM for S25HM, S27HM, HS50 , HS60 SW Version GEM 503.02
HOST Interface Manual
Page 66 of 243 ©Siemens AG, all rights reserved
used in: S6F6
HCACK - Host Command Parameter Acknowledge Code
Format: B[1]
0 = Accept, Command has been performed
1 = Command does not exist
2 = Cannot perform now
3 = At least one parameter is invalid
4 = Acknowledge, command will be performed with completion signaled later by an
event
5 = Rejected. Already in desired condition
6 = control state is not remote
7 = recipe not in library
8 = control mode is not „GEM-Host“
9 = bad PP-Body
10 - 63 reserved
used in: S2F42
HEADID – ID of the head within a gantry
Format: U2
In this version there is only 1 head per gantry. HEADID is always = 1.
HEIGHTOFREVOLVER - distance between the head and the transport conveyor
During the reference run, the SIPLACE machines measures the difference between the
upper edge of the transport conveyor and the nozzle on segment 1. The
HEIGHTREVOLVER is then calculated by subtracting the length of the nozzle on segment
1 form the measured value. The nozzle length is defined in the machine data. So
HEIGHTREVOLOR is a relative, not an absolute value.
Format:I4
Units are 1/1000 mm
used in : HEIGHTREVOLVERx
JobName Name of the actual job
Format:A
used in: TRACE_PCB_DATA
LeadCount - Number of lead found during package form measurement
Format: U2
used in: PLACEINFOREVx
Length - Length of a package form
Length is returned from the vision system. It’s the „optical“ length of the package form.
Units are 1/1000 mm
Format: U4
used in: PLACEINFOREVx
SIPLACE GEM for S25HM, S27HM, HS50, HS60 SW Version GEM 503.02
HOST Interface Manual
©Siemens AG, all rights reserved page 67 of 243
Level - Level in the matrix tray changer
Level 1 is the lowest level in matrix tray changer, level 40 the top most. A value of 0
indicates the manual tray.
Format: I2
used in: PICKUPINFOREVx
LIMITACK - Acknowledgment code for variable limit attribute set
Format: B[1]
1 = LIMITID does not exist
2 = UPPERDB < LIMITMAX
3 = LOWERDB >LIMITMIN
4 = UPPERDB < LOWERDB
5 = Illegal format specified for UPPERDB or LOWERDB
6 = ASCII value cannot be translated to numeric
7 = Duplicate limit definition for this variable
>7 = Other errors
8 - 63 reserved
used in: S2F46
LIMITID - Limit ID
Format: B[1]
used in: S2F45, S2F46, S2F48
LIMITMAX - maximum limit
Format:
used in: S2F48
LIMITMIN - minimum limit
Format:
used in: S2F48
LOCATION - Group of feeders 1..4
For a detailed description see „1.6 Machine Areas"
Used in LOCATION, PICKINFOREVx, PICKUPERRORSLOCx, TRACKFULL,
TRACKEMPTY
LOWERDB - lower boundary of the deadband for a limit
Format
used in: S2F45, S2F48
LRACK - Limit Report Acknowledge Code
Format: B[1]
0 = Accepted
1 = Denied. Insufficient space
2 = Denied. Invalid format
3 = Denied. At least one CEID link already defined
4 = Denied. At least one CEID does not exist