3OM-1286-007_w.pdf - 第333页

7-2 AJQEDT -ID PCB transfer speed des Avoid comp deviations Input Speed 1 [mm/sec] Speed 2 [mm/sec] Acceleration [G] Output Speed 1 [mm/sec] Speed 2 [mm/sec] Acceleration [G] Stop position control Input T imer [msec] Pos…

100%1 / 343
7-1
AJQEDT-ID
0606-005
Pattern Program Data Sheets
Pattern Program Data Sheets
Pattern Program Name
Comment 1
Comment 2
Date of Preparation
Prepared by
Operation Data
PCB Data
PCB size X (Horizontal) [mm]
Y (Vertical) [mm]
T (Thikness) [mm]
PCB origin
of
fset
X (Horizontal) [mm] + / -
Y (Vertical) [mm] + / -
Z [deg] + / -
XY-Angle [deg] + / -
X-Direction Same / Opposite
Y-Direction Same / Opposite
Z Angular Orientation Same / Opposite
PCB height offset [mm] + / -
Placement reference Rear Left/Front Left/Front Right/
Rear Right
PCB locate sequence Standard/Mode #1
PCB transfer sequence Synchronous Priority/Output Priority
Pre-Placed com-
ponent thickness
T
op [mm]
Bottom [mm]
PCB transfer
speed
Input Standard/Low Speed 1/Low Speed 2/
Low Speed 3/Specification V
alue
Output Standard/Low Speed 1/Low Speed 2/
Low Speed 3/Specification Value
7-2
AJQEDT-ID
PCB transfer
speed des
Avoid
comp
deviations
Input Speed 1
[mm/sec]
Speed 2
[mm/sec]
Acceleration
[G]
Output Speed 1
[mm/sec]
Speed 2
[mm/sec]
Acceleration
[G]
Stop
position
control
Input T
imer
[msec]
Position [mm]
Position-
ing 1
T
imer
[msec]
Position [mm] + / -
Output T
imer
[msec]
Position [mm] + / -
Input Conveyor
Y Position arrange speed setup (% deceleration) [%]
Output Conveyor
Y
Position arrange speed setup (% deceleration) [%]
PCB Locate
mode
Operation
The 1st sp dclr setting
([%] deceleration) [%]
The 2nd sp dclr setting
([%] deceleration) [%]
Std / Specification value
Z clamp
Delay T
imer 1
[msec]
Delay Timer 2
[msec]
Operation waiting time
[msec]
Placement mode Placement / Pass
Recovery
regulation
U-N Disable / Enable
Block Sort Disable / Enable
0606-005
Pattern Program Data Sheets
7-3
AJQEDT-ID
Pattern Program Name
Comment 1
Comment 2
Date of Preparation
Prepared by
Operation Data
PEC Recognition Data
PEC recognition function Disable / Enable
Correction algorithm Standard/Mode #1
PEC recognition Mode Global Zone 1 Disable/1 Point/2 Point/3 Point
Zone 2 Disable/1 Point/2 Point/3 Point
Zone 3 Disable/1 Point/2 Point/3 Point
Zone 4 Disable/1 Point/2 Point/3 Point
Zone 5 Disable/1 Point/2 Point/3 Point
Image Disable / Enable
Local Disable / Enable
Fiducial mark Zone 1
#1 X (Horizontal) [mm] + / -
Y
(Vertical) [mm] + / -
Mark Code
#2 X (Horizontal) [mm]
+ / -
Y
(Vertical) [mm] + / -
Mark Code
#3 X (Horizontal) [mm]
+ / -
Y
(Vertical) [mm] + / -
Mark Code
Zone 2 #1
X (Horizontal) [mm] + / -
Y
(Vertical) [mm] + / -
Mark Code
#2 X (Horizontal) [mm]
+ / -
Y
(Vertical) [mm] + / -
Mark Code
#3 X (Horizontal) [mm]
+ / -
Y
(Vertical) [mm] + / -
Mark Code
Zone 3 #1
X (Horizontal) [mm] + / -
Y
(Vertical) [mm] + / -
Mark Code
#2 X (Horizontal) [mm]
+ / -
Y
(Vertical) [mm] + / -
Mark Code
#3 X (Horizontal) [mm]
+ / -
Y
(Vertical) [mm] + / -
Mark Code
0606-005
Pattern Program Data Sheets