JUKI贴片机错误代码集合 - 第113页
E501852 “ The t ype of the holder is different.(Type2) ” “ 固定器类型 不同（ Type2 ） 。 ” E501853 “ The t ype of DTS is different.(Lane1) ” “ DTS 类型不同（ Lane1 ） 。 “ E501854 “ The t ype of DTS is different.(Lane2) ” “ DTS 类型不同（ Lan…
“[图像]未知要求(程序错误)”
[Cause]
This is a program error.
[Treatment]
Please take a note of the error code and contact our technical service dept. for information.
E501500 “There is no verification device.”
“不存在数值检查设备。”
E501501 “The verification device is an unused unit.”
“没有使用数值检查设备。”
E501502 “Supply of the component is no CVS.”
“不是对应 CVS 的组件。”
E501600 “Using the unused setting of the head when product is executed last time|%s| becomes with using the
unused setting of a present head.|Resume the product cannot be executed.”
“前一次生产时的 Head 使用情况和|%s| ，与现在 Head 的使用情况不相同，|不能继续生产。”
E501601 “The %d nozzle does not suffice in the number being set in ATC now.|Number of %d nozzle when
production is executed last time (%d)|.Resume the product cannot be executed.”
“现在 ATC 上设置的%d 吸嘴个数不够用，|前一次生产时%d 吸嘴个数：%d|不能继续生产。”
E501700 “Because the PWB is clamped, it is not possible to begin to produce.| The PWB free.| Begin to
produce again.”
“ 因为基板夹住，所以不能开始生产。 “
E501710 “The transportation motor cannot be moved because there is a PWB in the transportation road.”
“ 因为传送轨道上有基板，所以不能移动传送轨道。 “
E501800 “Failed in reading the correspondence error file because of production program check.”
“ 生产程序读一致性出错文件时失败。 “
E501810 “The error occurred in the placing pursuit.”
“ 贴片跟踪时发生错误。 “
E501820 “Position of Z axis is low.”
“ 因为不是 Z 轴的移动范围之内，所以不能移动。”
E501850 “Because MTS is used, parts cannot be put on rear.”
“ 因为使用 MTC，所以不能后面放组件。”
E501851 “The type of the holder is different.(Type1)”
“ 固定器类型不同（Type1）。 “
E501852 “The type of the holder is different.(Type2)”
“ 固定器类型不同（Type2）。”
E501853 “The type of DTS is different.(Lane1)”
“ DTS 类型不同（Lane1）。 “
E501854 “The type of DTS is different.(Lane2)”
“ DTS 类型不同（Lane2）。 “
E501855 “The part name is different.”
“ 组件名不同。”
E501856 “The installation hole position becomes.”
“ 安装空位置不同。 “
E501857 “It is a multi tray.”
“ 多型托盘状态。”
E501858 “The type of feeder is different.”
“ 送料器类型不同。 “
E501880 “The nozzle cannot be returned. continue anyway?”
“ 放回吸嘴时失败， 是否继续处理？ “
E501999 “Abnormal stop <%s>“
“异常结束生产。<%s>“
[Cause]
This error occurs when an action does not end normally.
an action that was taking place when a production ended abnormally.
While transporting PWBs
While recognizing VCS
While recognizing IC marks
While recognizing BOC marks
While detecting bad marks
Placement position
Pick position
While recognizing L3
While installing a nozzle on a head
While returning a nozzle to ATC
While disposing a component
While reading bank marks
Other positions
[Treatment]
A detailed error message should have been shown prior to this message.
Please check and see the status, using the given error number.
E502999 “Abnormal stop. (%ld)”
“异常结束生产。(%ld)”
E503001 “Retry List message file (RETRYLIST.MSG) cannot be opened”
“不能打开重试列表提示文件(RTRYLIST.MSG)。”
[Cause]
Failed to open the Retry List message file.
[Treatment]
Please re-install the system.
E503100 “You try to set remain less than level now, OK?”
“组件剩余数小于标准值，是否继续设置？”
[Cause]
The number of components remaining becomes less than the warning level of the number of
components left.
[Treatment]
Yes : Sets the entered number of components remaining.
No : Gets you back to the number of components remaining that is before you set.
E503200 “It is not Program made by setting non-stop. A normal operation is not occasionally done when
producing as it is. Production start forcibly?”
“生产程序不适用不间断生产|(不间断生产已被选用)，|或者弃用不间断生产，或者修改生
产程序。”
[Cause]
This message appears when the Non-stop functionality is enabled in the Operation Option but the
production program does not take Non-stop.
[Treatment]
Please disable the Non-stop functionality in the Operation Option, or check the Pick data in the
production program.
W503201 “It is not Program made by setting MTC non-stop.|(The MTC non-stop operation is selected.)|Make
the function of the MTC non-stop be unused by the operation option or try to program production.”
“ 生产程序不适用 MTC 不间断生产|(MTC 不间断生产已被选用)，| 或者弃用 MTC 不间断
生产，或者修改生产程序。”
W503202 “It is not Program made by setting DTS non-stop.|(The DTS non-stop operation is selected.)|Make
the function of the DTS non-stop be unused by the operation option or try to program production.”