LBO 27 Zoll - 第50页
2 Assembly instructions LBO 27" SIPLACE X4 LBO 27" 09/2007 Edition 50 2.4 Scope of delivery – Product license (00373 251) – 1 stopper unit for P A1 pre-assembled with cable loom – 1 stopper unit for P A2 pre-as…
LBO 27" 2 Assembly instructions LBO 27" SIPLACE X4
09/2007 Edition
49
2 Assembly instructions
LBO 27" SIPLACE X4
2.1 Function principle
The special design LBO 27” can only be used together with the special design 00176092-xx. 2
The delivered units for processing area 1 (PA1) and processing area 2 (PA2) are pre-assembled
for installation in machines with the stationary conveyor side wall on the right. 2
2.2 Requirements
Hardware: X4, (Single-conveyor, stationary conveyor side wall on right) 2
Software: 603.24IN-01.47.1 2
2.3 Restrictions
– The minimum PCB-width with the LBO 27” is about 240 mm.
– The minimum PCB-thickness is 2,5 mm.
– The maximum PCB-thickness is 6,5 mm.
– The maximum PCB-bowing is 0,5 mm.
– The maximum component height on the bottom side of the PCB is 21 mm.
– In combination with the special design the restrictions concerning the PCB-barcode still apply.
– The cycle-time delays about 2 seconds per PCB during to the slower conveyor-velocity.
– The lifetime of the conveyor-belts will decrease because of the higher PCB-weight.
2
2
2
2
2
2
2
2
2 Assembly instructions LBO 27" SIPLACE X4 LBO 27"
09/2007 Edition
50
2.4 Scope of delivery
– Product license (00373251)
– 1 stopper unit for PA1 pre-assembled with cable loom
– 1 stopper unit for PA2 pre-assembled with cable loom
– 2 Tee connectors for PUN 6 hose (with short piece of hose)
– 4 hexagon socket screws M6 x 40 mm
– 2 connecting cable sets (00372253-01)
– 1 hose PUN 6 with quick lock short (120 mm)
– 1 hose PUN 6 with quick lock long (2140 mm)
– Test-PCB for stopper adjustment (236 mm length)
– Cable ties
– Cable clips small
– Cable clips returnable
– Hyperterminal CD
2
2
LBO 27" 2 Assembly instructions LBO 27" SIPLACE X4
09/2007 Edition
51
2.5 Safety instructions
WARNING
The safety instructions from the “Operational safety” chapter of the user manual and servicing in-
structions take precedence over these instructions. 2
The SIPLACE placement machines are supplied with main power voltage.
Consequently parts of these systems carry dangerous voltages! This voltage is present at certain
modules inside the machine base, even when the machine is switched off at the main power
switch.
Incorrect handling of the placement machine or touching live parts of the machine can result in
death or severe injury, and considerable damage to equipment.
BEFORE starting any work, shut down the operating system correctly, then switch the machine
OFF at the main power switch and disconnect from the main power supply. In addition, the com-
pressed air supply must be switched off at the compressed air unit's main valve in the machine
base and vented by actuating the needle valve on the compressed air unit.
There is DANGER for heart pacemaker wearers in the vicinity of the linear motors, as described
in detail in the "Special safety instructions for working in the vicinity of strong magnetic fields"
section of the user manual and service manual.
Always follow the accident prevention regulations, DIN or other standards and special safety
rules applicable in your country.
Pay attention to the information concerning residual voltages in the Operational Safety chapter.
Follow the ESD regulations as described in the operational safety section of the operating
instructions.
During the retrofit, always secure the machine to prevent access by other people and to prevent
it being switched on again. The procedure is described in the "Lock out and tag out procedure"
section of the user manual.
Working with the SITEST program further increases the risk of accident.
The SITEST program must only be used by authorized and trained personnel.
2
2.5.1 Definitions
2
Note 2
2
2
2
Caution 2