LBO 27 Zoll - 第90页
2 Assembly instructions LBO 27" SIPLACE X4 LBO 27" 09/2007 Edition 90 2.8 Changes in SIPLACE PRO The option must be entered in the line configuration in SIPL ACE PRO and in the set-up. 2 2.8.1 Line configuratio…
LBO 27" 2 Assembly instructions LBO 27" SIPLACE X4
09/2007 Edition
89
23, 1, // type vacuum tooling = vacuum tooling with 2 vacuum sensors 2
24, 0, // no verification of clamping with motor 2
41, 0, // left side fixed, width adjustment 2
43, 0, // fixed rails pitch (actual) 2
44, 0, // fixed rails pitch (target) 2
48, 65, // [%] force stepping motor width adj. 2
49, -993, // [um] offset width adjustment 2
50, -3813, // [um] offset fixed rail 2
47, 1, // position fixed rail ok 2
60, 991, // [um] calibration position 1, width adj. 2
61, 21513, // [um] calibration position 2, width adj. 2
62, 326, // [um] cavity driver, input, width adj. 2
63, -447, // corr. a0, sensor width adj., input 2
64, -952, // corr. a1, sensor width adj., input 2
65, 118, // corr. a2, sensor width adj., input 2
66, 384, // [um] cavity driver, output, width adj. 2
67, -369, // corr. a0, sensor width adj., output 2
68, -598, // corr. a1, sensor width adj., output 2
69, 121, // corr. a2, sensor width adj., output 2
70, 365, // [um] cavity driver, middle, width adj. 2
71, -150, // corr. a0, sensor width adj., middle 2
72, -1952, // corr. a1, sensor width adj., middle 2
73, 397, // corr. a2, sensor width adj., middle 2
80, 60, // [mm/s] velocity stopper 2
81, 350, // [mm/s] velocity sensor stopper 2
82, 25, // [0.1m/s²] deceleration stopper 2
83, 600, // [ms] drive-up time stopper 2
84, 60, // [mm/s] velocity stopper LBO 2
85, 300, // [mm/s] velocity sensor LBO 2
86, 25, // [0.1m/s²] deceleration stopper LBO 2
87, 1250, // [ms] drive-up time stopper LBO 2
88, 10, // [%] velocity split for combined PCB 2
89, 200, // [ms] drive-up time stopper comb. PCB 2
90, 10, // [mm] bumper height LT (=0->40mm clearance) 2
2
: Close Hyperterminal.
: Remove the connection cable and push the transport control unit back into the case, screw in
the removed screws.
: Reboot the machine, to make sure that all changings are valid. The Adjustment is now finished.
This value has to be 1250 ms
2 Assembly instructions LBO 27" SIPLACE X4 LBO 27"
09/2007 Edition
90
2.8 Changes in SIPLACE PRO
The option must be entered in the line configuration in SIPLACE PRO and in the set-up. 2
2.8.1 Line configuration
: Select a line and check the Long board check box.
2
2
2
2
2
2
Click on Long board Select the lineClick on Long board
LBO 27" 2 Assembly instructions LBO 27" SIPLACE X4
09/2007 Edition
91
2.8.2 Set-up
: Select a set-up (see screenshot).
: For the PCB conveyor, select "Long board" and enter the value 236,000 under "Stopper 2 at
position" for both processing areas.
2
2
2
The stopper position is not included in the optimization unless the "Use for optimization" box is
checked. 2
2
Select the set-up
Enter 236.000
Select Long board