00196715-01_IM_SSW_704_DE_EN.pdf - 第10页
Installation Manual, Station Software Version 704.01 04/2010 Edition 10 of 60 3.3 Upgrading from 701.xx sof tware versions (X4I placement machine) → Download the SIPLACE_Prepare_703.02_Hotfix01.exe file from the Software…
Installation Manual, Station Software Version 704.01 04/2010 Edition
9 of 60
3.2 Upgrading from the 703.01 software version
3.2.1 SX-series placement machines
→ SX-series placement machines in the field:
Due to the SW component counter, the HCU/GCU and sensor modules have to be programmed. For
this, perform the work steps that are described in the Technical Informations TI2010-02V01 and
TI2010-02C01 about programming HCU/GCU for the 704 upgrade. These work steps can only be
performed by Siemens Service.
→ Exchange the X/Y sensor modules to X-03068500-03 / Y-03064608-03.
→ Install the 704.01 station software.
→ Shut down the machine.
→ Remove the tables.
→ Switch on the machine again and wait until all error messages have been displayed and the eSW
download menu is enabled.
→ Perform the eSW download for all subsystems.
→ Reboot the machine.
→ Place the tables.
The eSW download for the feeders starts automatically.
→ Save the calibration data for the placement heads (except Twin Head) in the EEPROM (see section
7.8).
→ Calibrate the machine by performing the following steps:
− Calibrate the gantry axis (activate the options Y-axis: Encoder Alignment, Travel
range, X-axis: Parameterization, Y-axis: Mapping in the list).
− Perform PCB and head mapping.
→ Start the production.
3.2.2 X-series placement machines
→ Install the 704.01 machine computer software for two-computer operation, see chapter 5.
→ Install the Vision computer software, see chapter 6.
→ Shut down the machine.
→ Remove the tables.
→ Switch on the machine again and perform the eSW download.
→ Reboot the machine.
→ Place the tables.
The eSW download for the feeders starts automatically.
→ Save the calibration data for the placement heads in the EEPROM (see section 7.8).
→ Start the production.
Installation Manual, Station Software Version 704.01 04/2010 Edition
10 of 60
3.3 Upgrading from 701.xx software versions (X4I placement machine)
→ Download the SIPLACE_Prepare_703.02_Hotfix01.exe file from the Software Downloadcenter and
execute the file.
→ Reboot the machine and perform an eSW download for the placement heads.
→ Install the 704.01 machine computer software for two-computer operation, see chapter 5.
→ Install the Vision computer software, see chapter 6.
→ Shut down the machine.
→ Remove the tables.
→ Switch on the machine again and perform the eSW download.
→ Reboot the machine.
→ Place the tables.
The eSW download for the feeders starts automatically.
→ Save the calibration data for the placement heads in the EEPROM (see section 7.8).
→ Calibrate the nozzle changer.
→ Calibrate the conveyor.
→ Start the production.
3.4 Upgrading from 60x software versions (X-series placement machines)
By upgrading from 60x station software versions, a complete reinstallation/recalibration and mostly also a
hardware rebuilding will be necessary. For this, a corresponding upgrade package is available, that can be
installed by Siemens Service if required.
Ser.No. B001 – B325: cannot be upgraded to the 70x software.
Ser.No. B326 – B599: can only be upgraded to the 70x software by a service team from Munich.
Ser.No. B600 – B751: Update of CAN node and upgrade of the C&P20 nozzle changer to the -04 version
required.
As of Ser.No. B752 the software upgrade to the 70x software can be performed without any hardware
rebuildings.
In the following flowchart all steps are described that have to be performed for the upgrade. At a glance,
these are:
- Downloading the eSW file from the installation CD (directory Upgrade_Preparation_704.01/60x) and
executing an eSW download for the placement heads (TQM) with CACCIA from a service PC (not for
C&P6/12 placement heads)
- Preparing Box PCs and hardware (see flowchart)
- Installing Windows XP Embedded (recommended) or Windows XP on both Box PCs
- Installing the 704.01 machine computer software for two-computer operation, see chapter 5
- Installing the Vision computer software, see chapter 6
- Shutting down the machine
- If necessary, performing hardware rebuildings
Installation Manual, Station Software Version 704.01 04/2010 Edition
-
Removing the tables
- Switching on the machine again
- Performing an eSW download (see flowchart)
- Performing complete calibration with PCB and head mapping
Note:
- It is also possible to send the mapping files that you have saved before to Siemens
Service. The files will be converted and resent to you. If you re-import the converted
mapping files, no PCB/head mapping has to be performed.
- Starting the production
11 of 60