2OM-1088-002.pdf - 第348页
Tg0699-PM-D2 θ -Axis Ball Screw Apply grease to the grease nipple with a grease gun. Lubrication θ -Axis Linear Guide Apply grease with a brush or a spatula. Lubrication Fig. 5A38 T able Section 8. Half-Y early Maintenan…
Tg0699-PM-D2
Fig. 5A35 Table Section
8. Half-Yearly Maintenance
0207-001 Chapter 3 1-28
X-Axis Ball Screw
(1) Move the table Z axis up
to the printing position.
(2) Detach the cover located
at the front side of the
table.
(3) Apply grease with a brush
or a spatula.
Lubrication
X-Axis Linear Guide
Front Side : Apply grease with a brush.
Rear Side
Note : Remove waste thread if any.
Clean the linear guide using the following procedure.
1. Press the "Table Section" tab on the "MNL OPN" submenu window in the "SPECIAL SEL."
menu.
2. Press the [Table Up (Trans - Retrt. - Correct - Prn.Pos.)] button to lift the table.
3. Starting from the front side, apply grease on the linear guides located on the left and right
at the front and rear sides of the machine.
4. Press the [Chg. Pos. Move (Start)] button on the "Cleaning Chg." tab on the "PRODUCT
CHG." submenu window in the "AUTO OPN" menu, to secure the working space.
5. Starting from the rear side, apply grease on the linear guide located at the center on the
rear side of the machine.
Cleaning
Fig. 5A36 Table Section
: Apply grease using a grease gun.
Tg0699-PM-D2
θ-Axis Ball Screw
Apply grease to the grease
nipple with a grease gun.
Lubrication
θ-Axis Linear Guide
Apply grease with a brush or
a spatula.
Lubrication
Fig. 5A38 Table Section
8. Half-Yearly Maintenance
0207-001 Chapter 3 1-29
Z-Axis Ball Screw
(1) Move the table Z axis up
to the printing position.
(2) Detach the cover located
at the front side of the table.
(3) Apply grease with a brush
or a spatula.
Lubrication
Z-Axis Guide Bushing
(1) Move the table Z axis up
to the printing position.
(2) Detach the cover located
at the front side of the table.
(3) Apply grease with a brush
or a spatula.
Lubrication
Z-Axis Guide Bush
(1) Lift the table up to the printing position by
pressing the [Table Up [ Trans - Retrt. -
Corect. - Prn. Pos. ]] button on the "Table
Section" in the "Manual Mode" Sub Menu
in the "Special Sel" menu.
(2) Detach the cover located at the front side
of the table.
(3) Apply grease with a brush or a spatula.
Lubrication
Fig. 5A37 Table Section
Tg0699-PM-D2
Ball Screw for Chute Width
Adjustment
(1) Move up the backup table
Z axis.
(2) Apply grease with a brush
or a spatula.
Lubrication
Linear Guide for Chute
Width Adjustment
(1) Move up the backup table
Z axis.
(2) Apply grease with a brush
or a spatula.
Lubrication
Backup Table Z-Axis Ball
Screw
(1) Move up the backup table
Z axis.
(2) Apply grease with a brush
or a spatula.
Lubrication
Fig. 5A39 P.C.B. Chuck Section
8. Half-Yearly Maintenance
0207-001 Chapter 3 1-30