2OM-1088-002.pdf - 第349页
Tg0699-PM-D2 Ball Screw for Chute Width Adjustment (1) Move up the backup table Z axis. (2) Apply grease with a brush or a spatula. Lubrication Linear Guide for Chute Width Adjustment (1) Move up the backup table Z axis.…
Tg0699-PM-D2
θ-Axis Ball Screw
Apply grease to the grease
nipple with a grease gun.
Lubrication
θ-Axis Linear Guide
Apply grease with a brush or
a spatula.
Lubrication
Fig. 5A38 Table Section
8. Half-Yearly Maintenance
0207-001 Chapter 3 1-29
Z-Axis Ball Screw
(1) Move the table Z axis up
to the printing position.
(2) Detach the cover located
at the front side of the table.
(3) Apply grease with a brush
or a spatula.
Lubrication
Z-Axis Guide Bushing
(1) Move the table Z axis up
to the printing position.
(2) Detach the cover located
at the front side of the table.
(3) Apply grease with a brush
or a spatula.
Lubrication
Z-Axis Guide Bush
(1) Lift the table up to the printing position by
pressing the [Table Up [ Trans - Retrt. -
Corect. - Prn. Pos. ]] button on the "Table
Section" in the "Manual Mode" Sub Menu
in the "Special Sel" menu.
(2) Detach the cover located at the front side
of the table.
(3) Apply grease with a brush or a spatula.
Lubrication
Fig. 5A37 Table Section
Tg0699-PM-D2
Ball Screw for Chute Width
Adjustment
(1) Move up the backup table
Z axis.
(2) Apply grease with a brush
or a spatula.
Lubrication
Linear Guide for Chute
Width Adjustment
(1) Move up the backup table
Z axis.
(2) Apply grease with a brush
or a spatula.
Lubrication
Backup Table Z-Axis Ball
Screw
(1) Move up the backup table
Z axis.
(2) Apply grease with a brush
or a spatula.
Lubrication
Fig. 5A39 P.C.B. Chuck Section
8. Half-Yearly Maintenance
0207-001 Chapter 3 1-30
Tg0699-PM-D2
8. Half-Yearly Maintenance
0207-001 Chapter 3 1-31
Fig. 5A40 P.C.B. Chuck Section
Z-Axis Guide Bushing
Clean the Bushing with an oiled rag.
Note : Remove waste thread if any.
Clean the guide using the following procedure.
Rear Reference :
Press the [Table Up (Trans - Retrt. - Correct - Prn.Pos.)] button on the "Table Section" tab on
the "MNL OPN" submenu window in the "SPECIAL SEL." menu to lift the table. Then, clean
the bushing starting from the front side, using a brush.
(a) For the guide bushing section upper than the flange, press the [PCB Backup
UP/DOWN (Origin - Start - End)] button on the "MNL OPN" submenu window in
the "SPECIAL SEL." menu to lift the PCB backup jig section and clean it.
(b) For the guide bushing section lower than the flange, press the [PCB Backup
UP/DOWN (Origin - Start - End)] button on the "MNL OPN" submenu window in
the "SPECIAL SEL." menu to lower the PCB backup jig section and clean it.
Front Reference :
Press the [Table Up] button on the "Table Section" tab on the "MNL OPN" submenu window in
the "SPECIAL SEL." menu to lift the table and clean the bushing using a brush.
• Starting from the front side, clean the guide bushings on the right and left at the front side of
the machine.
• Starting from the rear side, clean the guide bushings at the center on the rear side.
Secure the working space by pressing the [Chg. Pos. Move (Start)] button on the "Cleaning
Chg." tab on the "PRODUCT CHG." submenu window in the "AUTO OPN" menu, and then
clean the guide bushing.
(a) For the guide bush section upper than the flange, press the [PCB Backup
UP/DOWN (Origin - Start - End)] button on the "Table Section" tab on the "MNL
OPN" submenu window in the "SPECIAL SEL." menu to lift the PCB backup jig
section and clean it.
(b) For the guide bush section lower than the flange, press the [PCB Backup
UP/DOWN (Origin - Start - End)] button on the "Table Section" tab on the "MNL
OPN" submenu window in the "SPECIAL SEL." menu to lower the PCB backup
jig section and clean it.
Cleaning