00198442-04_UM_TX-V2_EN - 第97页

Instruction manual SIPLACE TX 2 Operational safety From software version 714.0 12/2020 2.7 Disabling the compressed air supply and discharging the pressure 97 2 Fig. 2.7 - 1 Compressed air unit on the placement machine L…

2 Operational safety Instruction manual SIPLACE TX

2.7 Disabling the compressed air supply and discharging the pressure From software version 714.0 12/2020

2.7 Disabling the compressed air supply and discharging

the pressure

The compressed air unit is at location 2 (see fig. 4.4 - 1, page 183 ). The compressed air working

pressure of the placement machine is set to 0.51 ± 0.01 MPa (5.1 ± 0.1 bar). The position of the

compressed air unit is shown at item 1 in fig. 2.7 - 1

, page 97. The supply of compressed air to

the placement machine can be interrupted with the shutoff valve (item 2 in fig. 2.7 - 1

, page 97 ).

 Use the machine key to release the cover lock.

 Lift the cover (see fig. 2.7 - 1, page 97 ).

 Turn the lever of the shutoff valve (item 1 of fig. 2.7 - 1, page 97) from the vertical to the hor-

izontal position.

 Monitor the operating pressure manometer (item 5 in fig. 2.7 - 1, page 97 ). When the place-

ment machine is switched on, the pressure discharges to 0 MPa (0 bar) within 1 minute.

CAUTION

Interruption to compressed air supply!

 When the placement machine is switched on, do not use the stop valve to interrupt

the compressed air supply for more than 30 minutes.

 If you need to shut off the pneumatic system for longer in order to carry out preven-

tive maintenance or servicing work, you must switch the placement machine off at

the main switch and disconnect it from the power supply.

Instruction manual SIPLACE TX 2 Operational safety

From software version 714.0 12/2020 2.7 Disabling the compressed air supply and discharging the pressure

Fig. 2.7 - 1 Compressed air unit on the placement machine

Legend for fig. 2.7 - 1

(1) Manometer for the placement machine component supply pressure

Target pressure: 0.51 ± 0.01 MPa, 5.1 ± 0.1 bar (display range 0 - 1.0 MPa, 0 - 10 bar)

(2) Manometer for supply pressure of gantries 1 to 2

Target pressure: 0.485 ± 0.01 MPa, 4.85 ± 0.1 bar (display range 0 - 1.0 MPa, 0 - 10 bar)

(3) Manometer for inlet pressure

Target pressure: 0.5 - 1.0 MPa, 5 - 10 bar (display range: 0 - 1.0 MPa, 0 - 10 bar)

(4) Compressed air supply for gantries

(5) Compressed air filter

(6) Compressed air connection

(7) Stop valve in the "OPEN" position

WARNING

Risk of injuries!

Risk of injuries from pressurized compressed air lines.

 NEVER detach compressed air lines while they are still pressurized.

(6)

(1)

(2)

(3)

(5)

(7)

(4)

2 Operational safety Instruction manual SIPLACE TX

2.8 Locking and attaching the warning labels From software version 714.0 12/2020

2.8 Locking and attaching the warning labels

2.8.1 Purpose and scope

Before performing any preventive maintenance work or service work to the placement machine,

a procedure of locking and tagging must be followed. The following procedure, when followed cor-

rectly, eliminates the possibility of an employee being injured by electrical shock in connection with

unexpected movement.

2.8.2 Description

Whenever it becomes necessary to isolate, control and release energy for the placement ma-

chine, the following procedure is to be followed.

 Notify affected employees.

 Switch off the placement machine and any auxiliary devices. Carry out all normal stopping

procedures:

– Press the stop button.

– Shut down the control computer.

– Switch the placement machine off at the main power switch.

 Isolate the placement machine from all its energy sources:

– Shut off the compressed air supply

– Shut off the main power supply

 Lock out the machine.

– Attach a lock whenever possible (e.g. to the main switch).

PLEASE NOTE

Minimum requirements

These procedures represent the minimum lock/tag out requirements for the preventive

maintenance or service work on the placement machine. Any additional safeguards

needed to complete work safely can be specified by facilities supervision, the safety of-

ficer, the safety committee and the health department.