Printer 710_810 v8 High Throughput Conveyor Module - 第35页

HIGH THROUG HPUT CONVE YOR (HTC ) MODULE REPLACEMENT PROCEDURES Chapter Issue 3 Oct 06 Technical Reference Manual 17.35 6. Fit t he rear s nugger plate , don’t tighte n the M4 pan head securing s crews. 7. T urn the pneu…

100%1 / 40
HIGH THROUGHPUT CONVEYOR (HTC) MODULE
REPLACEMENT PROCEDURES
17.34 Technical Reference Manual Chapter Issue 3 Oct 06
4. Fit the appropriate snugger base plate to the rear rail and secure using the
M4 pan head screws.
5. Fit the appropriate front snugger plate to the front rail and secure using the
M4 pan head screws.
Snugger Base Plate -
Fixed Width Chase
Snugger Base Plate -
Adjustable Screen Mount (ASM)
Front Snugger Plate -
Fixed Width Chase
Front Snugger Plate -
Adjustable Screen Mount (ASM)
HIGH THROUGHPUT CONVEYOR (HTC) MODULE
REPLACEMENT PROCEDURES
Chapter Issue 3 Oct 06 Technical Reference Manual 17.35
6. Fit the rear snugger plate, don’t tighten the M4 pan head securing screws.
7. Turn the pneumatic switch On, located on a magnetic plate on the right hand
side of the machine.
8. Load the product file to be printed, the rear rail moves to set the board width.
NOTE
With Auto Rail Width in Options Parameters set to Disabled the rear rail does
not set the board width during initialisation, but it can still be moved in
diagnostics.
9. Under Setup select Machine.
10. Select Basic Parameters.
11. Set Clamp Type to Snuggers.
12. Set Snugger Thickness to the thickness of the board.
13. Load a product board.
14. In Diagnostics select Rail System.
15. Select Toggle Board clamp, the rear snugger plate aligns with the board
edge.
Rear Snugger Plate
Front Snugger Plate
Downstops
Plan View of Rail System
Snugger Base Plate
HIGH THROUGHPUT CONVEYOR (HTC) MODULE
REPLACEMENT PROCEDURES
17.36 Technical Reference Manual Chapter Issue 3 Oct 06
16. Tighten the two rear snugger plate securing screws.
17. Using a 2mm Allen key adjust the two downstops on the snugger base plate,
(previous figure refers) to ensure that the top of the snugger base plate is
flush with the top of the board.
18. Repeat Step 17 on the front snugger plate.
19. Remove the board from the printer.
NOTE
The Board Clamp Setting procedure is not required after board clamp/foil-less
clamp to snugger replacement.
Snuggers to Clamps
WARNING
BOARD CLAMPS. EXTREME CARE MUST BE EXERCISED WHEN WORKING IN
THE TOOLING AREA OF THE MACHINE TO AVOID INJURY. THE FOILS ON THE
FRONT AND REAR BOARD CLAMPS ARE VERY SHARP.
NOTE
This procedure is valid when converting to either board clamps or foil-less
clamps.
1. Open the front printhead cover.
2. On the rear rail, remove the two rear snugger plate securing screws and
remove the rear snugger plate.
3. On the rear rail, remove the snugger base plate securing screws and
remove the snugger base plate.
4. On the front rail, remove the front snugger plate securing screws and
remove the front snugger plate.
5. Fit the board clamp to the rear rail and secure using the M4 pan head
screws.
6. Fit the board clamp to the front rail and secure using the M4 pan head
screws.
7. If foil-less clamps have been fitted continue with Step 8. If board clamps
have been fitted go to Step 10.
Rear Snugger Plate
Front Snugger Plate
Downstops
Plan View of Rail System
Snugger Base Plate