Printer 710_810 v8 High Throughput Conveyor Module - 第7页

HIGH THROUG HPUT CONVE YOR (HTC ) MODULE ADJUS TMENT S AND SET TINGS Chapter Issue 3 Oct 06 Technical Reference Manual 17.7 14. Select Adjust , the foll owing window is displ ayed: 15. Using the Next , Previous , Incr . …

100%1 / 40
HIGH THROUGHPUT CONVEYOR (HTC) MODULE
ADJUSTMENTS AND SETTINGS
17.6 Technical Reference Manual Chapter Issue 3 Oct 06
ADJUSTMENTS AND SETTINGS
Rail Lifted Sensors 1. In Diagnostics select Rising Table.
2. Select Select Module.
3. Select Home Rising Table.
4. Select Run Diagnost, the table moves to the home position.
5. Select Exit.
6. Select Rail System.
7. Select Select Module.
8. Select Home Rail Width.
9. Select Run Diagnost, the rear rail moves to the home position.
10. Place a 0.5mm feeler gauge between the rail shock absorber on the rear
right rail transport leg and the rail stop bar (clatter bar). Adjust the vane
bracket using a 2.5mm Allen key, so that the sensor LED is On with a 0.5mm
feeler gauge fitted and Off with a 0.7mm feeler gauge fitted.
11. Repeat Step 10 for left hand end of rear rail.
12. Select Drive Rail To Board Width.
13. Select Run Diagnost.
Right Transport Leg
Rear Rail
Front View of Rail System
Left Transport Leg
Linear Bearing
Feeler Gauge
Rail Stop Bar
(Clatter Bar)
Opto Vane
Bracket
Opto Vane
Opto
Shock Absorber
Sensor LED
Enlarged View of Right Rail Opto
HIGH THROUGHPUT CONVEYOR (HTC) MODULE
ADJUSTMENTS AND SETTINGS
Chapter Issue 3 Oct 06 Technical Reference Manual 17.7
14. Select Adjust, the following window is displayed:
15. Using the Next, Previous, Incr. and Decr. keys, set the Board Width to
50mm.
16. Select Exit.
17. Select Drive Rail To Board Width, the rear rail moves to the new board
width.
18. Repeat Steps 10 and 11 for setting the vane at the 50mm width. Lock the
adjusting screws.
19. Select Home Rail Width.
20. Select Run Diagnost, the rear rail moves to the home position.
21. Repeat Steps 10 and 11 at the home position, adjust vanes if necessary.
22. Select Cycle Rails.
23. Select Run Diagnost, ensure the sensors LED are On over the full travel of
the rail.
Rail System Test Parameters
BOARD WIDTH
CYCLE COUNT
250.0
50
mm
Cycles
HIGH THROUGHPUT CONVEYOR (HTC) MODULE
ADJUSTMENTS AND SETTINGS
17.8 Technical Reference Manual Chapter Issue 3 Oct 06
Auxiliary Conveyor Sensors
Heavy Board
Positional
Adjustment
If heavy boards are being printed and causing damage to the conveyor board
stops, adjustment of the position of the sensor can be carried out to minimise
this effect. To adjust the position of the sensor carry out the following:
1. Power down the machine.
2. Remove the sensor mounting bracket screws from the underside of the front
rail of the auxiliary conveyors.
3. Reposition the sensor mounting bracket by utilizing the additional mounting
hole in the front rail.
4. Refit the sensor mounting bracket securing screws.
5. Power up and run the machine, checking for correct operation of the sensor.
Board Optos
WARNING
BOARD CLAMPS. EXTREME CARE MUST BE EXERCISED WHEN WORKING IN
THE TOOLING AREA OF THE MACHINE TO AVOID INJURY. THE FOILS ON THE
FRONT AND REAR BOARD CLAMPS ARE VERY SHARP.
Positional
Adjustment
If the current product has an unsymmetrical board outline, the position of the
board optos can be adjusted to cater for these products. To adjust the position
of the sensor carry out the following:
1. Power down the machine.
Rear View of Front HTC Rail
Mounting Bracket Securing
Bolts (in 2 positions)
Additional Mounting Hole