00192402-01 - 第64页

GEM for SIPLACE V7.01 Page 64 of 251 ©Siem ens AG, all rights reserved 6 = ASCII value cannot be translated to num eric 7 = Duplicate lim it definition fo r this variable >7 = Other erro rs 8 - 63 reserved used in: S2…

100%1 / 251
GEM for SIPLACE V7.01
©Siemens AG, all rights reserved page 63 of 251
6 = control state is not remote
7 = recipe not in library
8 = control mode is not „GEM-Host“
9 = bad PP-Body
10 - 63 reserved
used in: S2F42
+($',' – ID of the head
Format: U2
0 = first head in the machine (RV-Head)
1 = second head in the machine (IC-head in case of a F4/F5 machine, second RV-
head in case of a S20/S23 machine)
9 = not defined
+(,*+72)5(92/9(5 distance between the head and the transport conveyor
During the reference run, the SIPLACE machines measures the difference between the
upper edge of the transport conveyor and the nozzle on segment 1. The
HEIGHTREVOLVER is then calculated by subtracting the length of the nozzle on segment
1 form the measured value. The nozzle length is defined in the machine data. So
HEIGHTREVOLOR is a relative, not an absolute value.
Format:I4
Units are 1/1000 mm
used in : HEIGHTREVOLVER1, HEIGHTREVOLVER2, HEIGHTIC
/HDG&RXQW - Number of lead found during package form measurement
Format: U2
used in: PLACEINFOREV1, PLACEINFOREV2, VISIONDATAIC
/HQJWK- Length of a package form
Length is returned from the vision system. It’s the „optical“ length of the package form.
Units are 1/1000 mm
Format: U4
used in: PLACEINFOREV1, PLACEINFOREV2, VISIONDATAIC
/HYHO- Level in the waffle pack changer
Level 1 is the lowest level in waffle pack changer, level 28 the top most. A value of 0
indicates the manual tray.
If the component was picked up from a feeder Level will contain -1.
Format: I2
used in: PICKUPINFOREV1, PICKUPINFOREV2, LEVELNRIC
/,0,7$&. - Acknowledgment code for variable limit attribute set
Format: B[1]
1 = LIMITID does not exist
2 = UPPERDB < LIMITMAX
3 = LOWERDB >LIMITMIN
4 = UPPERDB < LOWERDB
5 = Illegal format specified for UPPERDB or LOWERDB
GEM for SIPLACE V7.01
Page 64 of 251 ©Siemens AG, all rights reserved
6 = ASCII value cannot be translated to numeric
7 = Duplicate limit definition for this variable
>7 = Other errors
8 - 63 reserved
used in: S2F46
/,0,7,' - Limit ID
Format: B[1]
used in: S2F45, S2F46, S2F48
/,0,70$; - maximum limit
Format:
used in: S2F48
/,0,70,1 - minimum limit
Format:
used in: S2F48
/2:(5'% - lower boundary of the deadband for a limit
Format
used in: S2F45, S2F48
/5$&. - Limit Report Acknowledge Code
Format: B[1]
0 = Accepted
1 = Denied. Insufficient space
2 = Denied. Invalid format
3 = Denied. At least one CEID link already defined
4 = Denied. At least one CEID does not exist
5 = Denied. At least one RPTID does not exist
>5 = Other errors
6 - 63 reserved
used in: S2F36
/9$&. - Variable limit definition acknowledge code
Format: B[1]
1 = Variable does not exist
2 = Variable has no limits capability
3 = Variable repeated in message
4 = Limit value error as desired in LIMITACK
5 - 63 reserved
used in: S2F46
0DFKLQH6LGH - Side of the machine
Format: U1
0 = right side in transport direction
1 = left side in transport direction
GEM for SIPLACE V7.01
©Siemens AG, all rights reserved page 65 of 251
9 = not defined
0D[%DOO'HY - Maximal ball deviation
MaxBallDev is calculated by the vision system during the optical centering of a package
form. It is calculated over all balls in all ball groups.
Format: F8
Units are 1/1000 mm
used in: PLACEINFOREV1, PLACEINFOREV2, VISIONDATAIC
0D[/HDG'HY - Maximum lead deviation
MaxLeadDev is calculate by the vision system during the optical centering of a package
form. It is calculate over all leads in all lead groups.
Format: F8
Units are 1/1000 mm
used in: PLACEINFOREV1, PLACEINFOREV2, VISIONDATAIC, COPLANARITYDATAIC
0'/1 - Equipment Model Type
Format: A
used in: S1F2, S1F13, S1F14, S1F65, S1F66
0+($' - Message block header associated with block in error
Format: B[16]
used in: S9F1, S9F3, S9F5, S9F7, S9F11
0,' - Lot ID
Format: A[16]
used in S2F27
QRWBFXELFBQR]]OH Vacuum value for a nozzle
vacuum threshold for melfs, etc.
Format: I4
Units are mbar
used in : VACUUMDATEREV1, VACUUMDATAREV2, VACUUMDATAIC
12==/(B7<3(: - Number of a nozzle
For a detailed description see „SIPLACE Placement Stations - Data Interface: Chapter
Nozzle Types“.
Format: U4
used in : NOZZLECONF1, NOZZLECONF2, NOZZLECONFIC, NOZZLERETURN
21/$&. Acknowledge for code for ON-LINE request
Format: B[1]
0 = Accepted
1 = Denied
2 = Equipment already ON-LINE
3 - 63 reserved
used in S1F18
RSHQBQR]]OH Vacuum value for a nozzle
vacuum value measured with an open nozzle