4M184002w_F8S - 第171页
Error ID Error Name, Description, Cause, and Remedy 400b01 Feeder preparation complete A pick up miss comp or disengaged Latch was detected. Open the safety cover and conrm that there is no interference with the head, a…
Error ID Error Name, Description, Cause, and Remedy
400921 Servo Alarm
Overload Alarm
Check out motor wiring or exchange both motor and driver. Either, Conrm that
the blocking exists with cutter pieces.
400931 Servo Alarm
Speed Alarm
Readjust motor gain.
400941 Servo Alarm
multi-cycle Error
Check out the motor wiring or exchange the motor.
400942 Servo Alarm
The value of variation counter is out of the range
Check out the wiring of Origin sensor. Or, Exchange driver.
400951 Servo Alarm
Power Drive detected temperature error
Ambient Temperature is high. Exchange driver.
400961 Servo Alarm
Sensor Error
Check Motor Encoder wires. Or, exchange the motor.
400962 Servo Alarm
Sensor Error
Check Motor Encoder wires. Or, exchange the motor.
400971 Servo Alarm
high drive Voltage
Insucient power. Exchange driver.
400972 Servo Alarm
Low drive Voltage
Check out the drive power wiring putted in Driver. Or, check out DC48V.
400991 Servo Alarm
Reading Error on permanent memory
Exchange the driver.
400992 Servo Alarm
Writing Error on permanent memory
Exchange the driver.
400998 Servo Alarm
CPU Error
Exchange the driver.
400999 Servo Alarm
Parameter Error
Conrm the changed value of Parameter.
400a08 Head Interlock Error
Releasing the brake is impossible during Servo On.
-----
3.1 Safety Device
4OM-1840
3-3-91604-001
Error ID Error Name, Description, Cause, and Remedy
400b01 Feeder preparation complete
A pick up miss comp or disengaged Latch was detected.
Open the safety cover and conrm that there is no interference with the head, and
then, release the ready feeder.
400c01 Nozzle stocker down time out
Nozzle stock unit lower bound detection 1 was not turned on in prescribed time.
Please conrm the lower bound detection 1 sensor of nozzle stock unit.
400c02 Nozzle stocker down time out
Nozzle stock unit lower bound detection 2 was not turned on in prescribed time.
Please conrm the lower bound detection 2 sensor of nozzle stock unit.
400c03 Nozzle stocker down time out
Nozzle stock unit lower bound detection 3 was not turned on in prescribed time.
Please conrm the lower bound detection 3 sensor of nozzle stock unit.
400c04 Nozzle stocker down time out
Nozzle stock unit lower bound detection 4 was not turned on in prescribed time.
Please conrm the lower bound detection 4 sensor of nozzle stock unit.
400d01 Software Interlock Error
Head1 NL axis's poor operation was detected, and the scram of the XY axis was
carried out.
Please perform a zeroing.
400d02 Software Interlock Error
Head2 NL axis's poor operation was detected, and the scram of the XY axis was
carried out.
Please perform a zeroing.
400d03 Software Interlock Error
NL axis(Head2) Interlock Detected.
Please conrm the nozzle has not fallen when you push the beam by the hand.
Please perform a zeroing.
400d04 Software Interlock Error
NL axis(Head1) Interlock Detected.
Please conrm the nozzle has not fallen when you push the beam by the hand.
Please perform a zeroing.
400d05 Software Interlock Error
L1 axis(Head2) Interlock Detected.
Please conrm the nozzle has not fallen when you push the beam by the hand.
Please conrm detection of Pass Line, excess pushing.
400d06 Software Interlock Error
L2 axis(Head2) Interlock Detected.
Please conrm the nozzle has not fallen when you push the beam by the hand.
Please conrm detection of Pass Line, excess pushing.
400d07 Software Interlock Error
L3 axis(Head2) Interlock Detected
Please conrm detection of Pass Line, excess pushing.
3.1 Safety Device
4OM-1840
3-3-101604-001
Error ID Error Name, Description, Cause, and Remedy
400d08 Software Interlock Error
L1 axis(Head1) Interlock Detected.
Please conrm the nozzle has not fallen when you push the beam by the hand.
Please conrm detection of Pass Line, excess pushing.
400d09 Software Interlock Error
L2 axis(Head1) Interlock Detected.
Please conrm the nozzle has not fallen when you push the beam by the hand.
Please conrm detection of Pass Line, excess pushing.
400d0a Software Interlock Error
L3 axis(Head1) Interlock Detected.
Please conrm the nozzle has not fallen when you push the beam by the hand.
Please conrm detection of Pass Line, excess pushing.
400f01 Safety Cover
Safety cover opened
Close the safety cover and lock it.
400f02 Safety Cover
Failed in locking Simplied Cover.
-----
400f03 Safety Cover
Failed in locking Auto Cover.
-----
401001 Cart
No Cart
There is a possibility that the Front/Rear of Cart is missing. Please put the cart in.
401101 Emergency Stop Switch
The [emergency stop] switch was pressed.
(Please conrm the nozzle has not fallen when you push the beam by the hand.)
Please switch on a power supply after canceling an emergency stop switch and
screen return to normal display.
401201 Safety Cover
The safety cover opened. [S131,S132]
Please shut a safety cover and push the [POWER ON] button.
401301 Shut-o Beam
The main circuit of the XY Beam was broken. [K33A,K33B]
-----
401401 Head1 Nozzle descending
Head1 nozzle descent was detected. [A-B3104]
Please perform a zeroing.
401501 Head2 Nozzle descending
Head2 nozzle descent was detected. [B-B3104]
Please perform a zeroing.
401601 Head1 Nozzle descending
Head1 descent was detected. [A-B3103]
Please perform a zeroing.
3.1 Safety Device
4OM-1840
3-3-111604-001