4M184002w_F8S - 第203页
Error ID Error Name, Description, Cause, and Remedy 424005 Stopper movement Error Output stop sensor is detected before output stopper goes up. PCB has reached the stopper . Please conrm that the start position for plac…
Error ID Error Name, Description, Cause, and Remedy
42360a Error in NR-L2 axis
Reserved Code
Reserved Function of driver. Please make inquiries when error is detected.
42360b Error in NR-L2 axis
Reserved Code
Reserved Function of driver. Please make inquiries when error is detected.
42360c Error in NR-L2 axis
Reserved Code
Reserved Function of driver. Please make inquiries when error is detected.
42360d Error in NR-L2 axis
Reserved Code
Reserved Function of driver. Please make inquiries when error is detected.
42360e Error in NR-L2 axis
Reserved Code
Reserved Function of driver. Please make inquiries when error is detected.
42360f Error in NR-L2 axis
System Error on NR-L2 axis
System Error of internal driver. Driver error is supposed if this problem happens
frequently.
423610 Error in NR-L2 axis
Communication Error on NR-L2 axis
1. Conrm connection to communication cable.
2. Conrm Power supply(24V).
3. Conrm the communication setting of PCI board.
4. Conrm the address of driver and communication rate setting.
5. Conrm Firmware of Driver.
424001 Stopper movement Error
Stop sensor was detected before positioning(R) stopper
There is a possibility that P.C.B. is pulled and raised in Stopper. Please conrm
P.C.B. stopping position.
424002 Stopper movement Error
Positoning(R) stopper was not completed within predetermined time.
1. Check out the P.C.B. between stopper and conveyor
2. Error in Up/Down detection sensor. Check out the sensor input
3. Disconnection, Error of Movement output. Please check Stopper by manual
movement if sensor input is proper.
4. Please set speed again by adjusting speed control when stopper is slow.
424003 Stopper movement Error
P.C.B. was detected on Stopper.
P.C.B is stop on the Stopper. Please conrm whether Conveyor has no Error.
424004 Stopper movement Error
Input stop sensor is detected before input stopper goes up.
PCB has reached the stopper. Please conrm that the start position for placement
PCB is correct.
3.3 Conveyor
4OM-1840
3-3-411604-001
Error ID Error Name, Description, Cause, and Remedy
424005 Stopper movement Error
Output stop sensor is detected before output stopper goes up.
PCB has reached the stopper. Please conrm that the start position for placement
PCB is correct.
424101 Detection of Input conveyor P.C.B.
P.C.B. was detected before starting placement from input machine
Please remove indenite P.C.B. from conveyor. Conrm whether P.C.B. is not
detected before P.C.B. transfer.
424102 Detection of Input conveyor P.C.B.
P.C.B. on Input conveyor is existing
Remove P.C.B. from Conveyor.
424201 Detection of output conveyor P.C.B.
P.C.B. was detected before starting output for output machine
Remove P.C.B. from Conveyor.
424202 Detection of output conveyor P.C.B.
The output for Output machine is completed, but P.C.B. on conveyor was detected
Remove P.C.B. from Conveyor.
424301 Detection of positioning conveyor(R) P.C.B.
No P.C.B. on conveyor
Output P.C.B. is not detected. Please conrm whether P.C.B. is detected correctly
or not.
424302 Detection of positioning conveyor(R) P.C.B.
The placement was completed, but P.C.B. was not detected.
Placed P.C.B. is not detected. Please conrm whether P.C.B. is detected correctly
or not.
425101 Detection of Input conveyor sensor
Decrease sensor was detected before starting
Remove P.C.B. from Input Conveyor.
425102 Detection of Input conveyor sensor
Decrease sensor was not detected before starting
Placing P.C.B. is not found internal machine.
1. Please put P.C.B. on the sensor
2. Because there is a possibility of P.C.B. falling, please conrm the width of
conveyor.
425103 Detection of Input conveyor sensor
Stop sensor was detected before starting
Remove P.C.B. from Input Conveyor.
425104 Detection of Input conveyor sensor
Stop sensor was Not detected before starting
Placing P.C.B. is not found internal machine.
1. Please put P.C.B. on the sensor
2. Because there is a possibility of P.C.B. falling, please conrm the width of
conveyor.
3.3 Conveyor
4OM-1840
3-3-421604-001
Error ID Error Name, Description, Cause, and Remedy
425105 Detection of Input conveyor sensor
P.C.B. on decrease sensor was detected after movement completion
Remove P.C.B. from Input Conveyor.
425106 Detection of Input conveyor sensor
P.C.B. on decrease sensor was not detected after movement completion
Please check whether P.C.B. is detected correctly.
Conrm whether the sensor doesn’t have Error.
425107 Detection of Input conveyor sensor
P.C.B. on stop sensor was detected after movement completion
Remove P.C.B. from Input Conveyor.
425108 Detection of Input conveyor sensor
P.C.B. on stop sensor was not detected after movement completion
Please check whether P.C.B. is detected correctly.
Check whether the sensor doesn’t have Error.
425109 Detection of Input conveyor sensor
P.C.B. on Input conveyor was detected
Remove P.C.B. from Conveyor.
42510a Detection of Input conveyor sensor
P.C.B. on Input conveyor was not detected
Please check whether P.C.B. is detected correctly. Check whether the sensor
doesn’t have Error.
42510b Detection of Input conveyor sensor
2 P.C.B. pieces on conveyor exist.
1. Remove it if unnecessary P.C.B. exists, when checking P.C.B. on Conveyor.
2. Please return PCB to Stop sensor of input conveyor when PCB on input
conveyor is taken on positioning conveyor.
42510c Detection of Input conveyor sensor
P.C.B. on sensor was detected in the state of not placing P.C.B.
There is a possibility whether P.C.B. is inserted or P.C.B. arrived before detecting
signals.
42510d Detection of Input conveyor sensor
Disengaged P.C.B. of Input conveyor
Possible to driver continuously.
Please conrm the state of P.C.B. if it is not removed purposely
42510e Detection of Input conveyor sensor
P.C.B. was not detected when placement was completed
P.C.B. from Input Machine is not received and sent.
Please conrm whether P.C.B. on Input conveyor is caught.
42510f Detection of Input conveyor sensor
P.C.B. was detected from Input conveyor sensor
P.C.B. is inserted though the mode that could not be inserted.
Please remove the inserted P.C.B..
425110 Detection of Input conveyor sensor
P.C.B. was detected from Input conveyor sensor
P.C.B. is inserted in P-OUT valid mode.
3.3 Conveyor
4OM-1840
3-3-431604-001