4M184002w_F8S - 第255页
Error ID Error Name, Description, Cause, and Remedy 4b2405 Feeder (Movement Error) Alarm Code:E4 - Positioning Completion T imeout (Foreign substances in the sprocket wheel) Conrm whether or not the tape is being jammed…
Error ID Error Name, Description, Cause, and Remedy
4b2307 Feeder (Servo Error)
Alarm Code:A6 - Others
-----
4b2308 Feeder (Servo Error)
Alarm Code:A7 - Fault Load Error (Tape twisting, Catching foreign substances)
Conrm whether or not the tape is being jammed on the path.
Conrm the reel to operate smoothly.
Conrm whether or not some components and dust are being caught in the
sprocket.
Conrm whether or not some components and dust are being caught in the tape
feeding gear.
4b2309 Feeder (Servo Error)
Alarm Code:A8 - Encoder Error (Breaking wire, Breakdown of control P.C.B. and
Defective servo motor)
Please replace the feeder.
4b230a Feeder (Servo Error)
Alarm Code:Ab - System Error
Please replace the feeder. (It may be caused by trouble of the control P.C.B..)
4b230b Feeder (Servo Error)
Alarm Code:Ac - Reckless Run Detection Error
Please replace the feeder. (It may be caused by trouble of the control P.C.B..)
4b230c Feeder (Servo Error)
Alarm Code:Ad - Excessive deviation in position
If the error occurs frequently, replace the feeder. (It may be caused by trouble of
the control P.C.B..)
4b2401 Feeder (Movement Error)
Alarm Code:E0 - (1) Damaged cover tape/ (2) Cover tape jammed in the storage/
(3) Splicing section peeling o
(1) Conrm whether or not the cover tape is set correctly
(2) Please remove the cover tape from the storage section.
(3) Please check the splicing condition if the work performed correctly in the
process.
4b2402 Feeder (Movement Error)
Alarm Code:E1 - Cover tape peeling o error (Get caught up)
(1) Conrm whether or not the cover tape is set correctly.
(2) Conrm whether or not some sticky material has adhered to the suppressor.
(3) Conrm the splicing condition if the work performed correctly in the process.
4b2403 Feeder (Movement Error)
Alarm Code:E2 - Origin Position Checking Error (Excessively out of the origin
during servo ON)
If the error occurs frequently, replace the feeder. (It may be caused by trouble of
the control P.C.B..)
3.8 Others
4OM-1840
3-3-931604-001
Error ID Error Name, Description, Cause, and Remedy
4b2405 Feeder (Movement Error)
Alarm Code:E4 - Positioning Completion Timeout (Foreign substances in the
sprocket wheel)
Conrm whether or not the tape is being jammed on the path.
Conrm the reel to operate smoothly.
Conrm whether or not some components and dust are being caught in the
sprocket.
4b2407 Feeder (Movement Error)
Alarm Code:E6 - Lane Change Timeout Error
If the error occurs frequently, replace the feeder. (It may be caused by trouble of
the control P.C.B..)
4b2408 Feeder (Movement Error)
Alarm Code:E7 - Servo ON Timeout
If the error occurs frequently, replace the feeder.
(It may be caused by trouble of the control P.C.B..)
4b2410 Feeder (Movement Error)
A pickup error occurred due to feeder operation problem.
Please check the feeder and the component.
-----
4b2411 Feeder (Movement Error)
Alarm Code:E5 - Redundant Order Error (A feeding error may occur.)
Conrm whether or not the tape is being jammed on the path.
Conrm the reel to operate smoothly.
Conrm whether or not some components and dust are being caught in the
sprocket.
Conrm whether or not some components and dust are being caught in the tape
feeding gear.
4b2412 Feeder (Movement Error)
Error in conrming connection of Feeder
Please check connection of Feeder
4b2413 Feeder (Movement Error)
Cannot send Tape because alarm is found in one side Lane of Dual Feeder.
Please execute recovery process, and then operate it again.
4b24a3 Feeder (Movement Error)
Feeder error (feeding time-out)
-----
4b2501 Splicing Operation failed
Alarm Code:E3 - (1)No supplied history/ (2)Dirty splicing detection sensor (dust
adhesion)
(1) Please operate to resupply components in the machine after splicing
operation.
(2) Please clean the joint detection sensor.
4b2601 Unit P.C.B. B.B.R. Information
There is no information in the relevant P.C.B. (on the Transfer Conveyor).
Delete the BBR information after removing the P.C.B..
3.8 Others
4OM-1840
3-3-941604-001
Error ID Error Name, Description, Cause, and Remedy
4b2602 Unit P.C.B. B.B.R. Information
There is no information in the relevant P.C.B. (on the Transfer XY-Table).
Delete the BBR information after removing the P.C.B..
4b2603 Unit P.C.B. B.B.R. Information
A problem was found in the unit PCB BBR information.
Delete the BBR information after removing the P.C.B..
4b2701 Start Process(Feeder Connection Error)
A special feeder is appointed. Please conrm the model of a set feeder.
-----
4b2711 Start Process(Feeder Connection Error)
ACV Check Error. Component ID on the feeder is not same as one specied by
current program.
-----
4b2713 Start Process(Feeder Connection Error)
There is a splicing failure feeder.
-----
4b2722 Start Process(Feeder Connection Error)
Feeder is not ready
-----
4b02803 PCB-ID communication Error.
A problem was found in the unit PCB ID information.
Delete the P.C.B.-ID information after removing the P.C.B.
4b2c01 Error in connection between CPU
Failed in communications with the Control CPU.
-----
4b2c02 Error in connection between CPU
Failed in communications with the Recog. CPU.
-----
4b3001 Cutter Error
Program Error(There is a operation mode which is not set)
-----
4b3002 Cutter Error
Cutter open error.
(1) Please conrm whether there is not the becoming shorter of chips.
(2) To a cutter open detection sensor trouble please conrm whether is clean.
(3) Please conrm whether there is not the trouble of the air valve.
(4) Please conrm whether there is not the trouble of the cylinder.
4b3003 Cutter Error
There is a time-out in Cutter-axis.(Zeroing operation start)
-----
4b3004 Cutter Error
Cutter-axis Time-out(Zeroing)
-----
3.8 Others
4OM-1840
3-3-951604-001