SIPLACE Station Software 7xx to 714 介绍 - 第159页
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition 159 The following checks can be perfo rmed: Checks CPP C&P20A C&P20 P Component sensor – Component sensor v oltage (contamination) – Hys…
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition
158
9.11 Conveyor Carrier X for Measurements
Compatible mode: Not supported
For machine accuracy measurements as i.e. ACT or MFU, the glass components in the waffle pack
tray and the glass plate had to be set up on the component table. If required, feeders had to be
removed for this. With the new Conveyor Carrier X, the waffle pack tray and the glass plate can
be set up via the board conveyor instead. Thus, an intervention in the customer setup is avoided
and time saved.
The Conveyor Carrier X occupies one virtual track on the table – like the Arbitrary Carrier X.
The Conveyor Carrier X must be set up manually on any empty track in an opened setup. The
waffle pack tray with the glass components must be set up manually on the carrier as well. Then
the carrier position and the conveyor lane (1 or 2) must be set in SIPLACE Pro.
Fiducials can be defined on the waffle pack tray for a higher pickup accuracy.
As the loaded waffle pack tray is always set to full component filling level, the operator must ensure
that the waffle pack tray is filled.
The board description for the Conveyor Carrier X has to be adapted in SIPLACE Pro. In case of
dual lane conveyor, the conveyor must be operated in synchronous dual conveyor mode.
Additionally, the operator must ensure that the waffle pack tray is available on the second lane.
Restrictions
– No travel range check.
– No pickup simulation.
– The Conveyor Carrier X uses one track on an X-table virtually. If the real table should be
completely occupied, the operator might have to remove a feeder from the table to create place
for the virtual feeder.
– No I-Placement mode.
– The SIPLACE Pro Optimizer does not consider the time it takes to fill up a tray with
components and change it.
9.12 Checking the Placement Heads
Compatible mode: Complete
To reduce unplanned machine stops, the placement heads can be checked with functions of the
SIPLACE Head Care Station. The functions are integrated in the station software and can be
performed for the CPP, C&P20A and C&P20 P placement heads on the Machine service activity
level. The head check mode and the placement head can be selected in the ToolTestBench view.
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition
159
The following checks can be performed:
Checks
CPP
C&P20A
C&P20 P
Component sensor
– Component sensor voltage (contamination)
– Hysteresis (detection of mechanical play)
X
X
X
Hold circuit (air-tightness)
X
X
X
Segment spring mechanism
– Path until addressing the light barrier
– Cushioning path of the segments
X
X
X
Z-axes travel range
– Segment guides (rough running)
X
X
X
Vacuum system
– Air-tightness
– Switching and control behavior of the pressure control valve
X
X
X
Endurance run with low force, Z-axes positioning mode
X
X
X
Endurance run light barriers, Z-axes positioning mode (default
sequence run)
X
X
X
Segment offset (mechanical damages on the segments)
X
X
X
Filter disks (presence and damage)
X
X
Switching disk (installation position)
X
X
DP rotation (DP positioning)
X
Component sensor calibration
X
Controlling the component sensor and light barrier values
dependent on the DP angle
X
Table 9-1: Checks for the placement heads
9.13 New Parameter Set for ECCOBOND D125F with 250µ Needle
Nozzle
To dispense larger glue dots more stably with the ECCOBOND D125F glue type, a new glue
parameter set for a 250µ needle nozzle has been included in the default parameter set. A new
system description (DIPF 1019) has been created to measure the needle nozzle.
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition
160
9.14 Wizard for Teaching Fiducials
Compatible mode: Complete
In previous SIPLACE Vision versions, the taught fiducials were created with an editor. In version
5.2.1, the editor has been replaced by a wizard with which the teaching can be performed in a
guided sequence. The intuitive user guidance ensures easy and safe creating of the taught fiducial
since the necessary actions are performed successively in the wizard.
The wizard consists of 4 views with the following actions:
1. Setting illumination
2. Specifying region of interest
3. Setting reference point
4. Checking result / Accepting data
The data remains completely compatible to previous SIPLACE Vision versions. I.e., the wizard
displays the data correctly if the fiducial has been taught with a previous version and the data that
has been taught with the wizard will be correctly used by previous versions.
9.15 No Support as of Station Software Version 708.0
– The "Modify/Change the component supply of a packaging unit" function has been removed
from the station software GUI. This function can only be performed in SIPLACE Setup Center.
The Configure package button has been removed from the Filling level view and
consequently, the next Fill level details view is not applicable anymore.
– The button for the SIPLACE service activity level has been removed from the GUI. Most
functions that were only available as of this activity level can now be used as of the Machine
service activity level.
– Messages before production (e.g. Remove the Support Pins) have been replaced by
Error details.
– The EventAnalyzer (EVA) is not supported anymore.
– The station software cannot be installed under the following operating systems anymore:
Windows Server 2003, Windows Server 2008 and Windows Server 2012, Windows XP,
Windows Vista and Windows 8.0.