SIPLACE Station Software 7xx to 714 介绍 - 第229页
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition 229 11.20 Twin Head – Placing Two Long but Narrow Compone nts in One Cycle Two long but narrow component s can now be placed in one Twin Head cy…
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition
228
● If WDTL is used, the data of the board located in the shuttle is stored to support auto recovery.
● Station-wise download is now supported together with the shuttle.
Restrictions
SIPLACE Pro does not send any information of the barcode position on the board top side.
11.16 Board Inspections – New Types
Compatible mode: Not supported
Additional inspections can be coupled to a placement position. The board camera is used for those
inspections.
Detailed information on the board inspections can be found in the Onboard PCB Inspection User
Guide, item no.: [00198375-xx].
11.17 Alternative Components – Enhancements
Compatible mode: Not supported
When alternative components are used, the station software now supports setup changes without
running the machine empty.
11.18 Temperature-Based Head Recalibration
Compatible mode: Not supported
The temperature sensor at the head plate is now used within the station software for recalibrating
the placement head on TX2 micron and TX2i micron placement machines. The temperature sensor
triggers recalibrations during production to achieve an optimal placement rate.
A new repetition strategy in the accuracy procedures ensures that recalibrations are performed
more often when the machine is changing rapidly (indicated by a change of the temperature) and
seldom when the machine reaches its operating point (indicated by a stable temperature).
11.19 Touchless Placement – New Placement Process
Compatible mode: Not supported
A new placement process has been introduced for placing very sensitive components in the chip
process. With the Touchless Placement process, components will be placed on a board for which
the position of height measurement points has been defined in SIPLACE Pro. Detailed information
can be found in the Touchless Placement User Guide, item no: [00198376-xx].
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition
229
11.20 Twin Head – Placing Two Long but Narrow Components in One
Cycle
Two long but narrow components can now be placed in one Twin Head cycle even if the
components have a diagonal bigger than a segment distance of 70.8 mm.
Example:
If these components are placed in an angle of 90 or 270 degrees, they do not collide during
teaching and placing.
11.21 Nozzles – New Concave Nozzles
Compatible mode: Not supported
The station software supports the new concave nozzles 1204, 2204 and 4204.
11.22 Long Board Option up to 1525 mm
Compatible mode: Complete
The licensed Long Board Option up to 1500 mm - Machine Connection license now supports
boards up to 1525 mm. The relevant settings must be enabled in SIPLACE Pro.
Detailed information on the Long Board Option can be found in the LBO User Manual,
item no.: [00197085-xx].
11.23 Automatic Calibration – System Identification for SX-series
Compatible mode: Complete
The System identification calibration feature has been introduced for the SX-series placement
machines in the automatic calibration. Therefore, an additional calibration step may be required
after the station software has been installed. Please refer to the Installation Manual,
item no.: [00198236-xx].
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition
230
11.24 Miscellaneous Improvements and Adaptions
11.24.1 Audible Signal for Indicator Lamps – New Pulse State
Compatible mode: Complete
The audible signal for the indicator lamps has been enhanced and now supports three states: On,
Off and Pulse (new). The Pulse state is like the lamp indicators flashing state.
Allowed pulse values: 50 ms on, 950 ms off.
The audible signal can be switched off in the Production view on the station software GUI.
11.24.2 Station Software GUI – Adaptions
Compatible mode: Complete
– For the following detailed errors, a button in the message bar is offered to confirm the error
directly:
40022 Position of dispenser nozzle has not been measured
40040 Reject plate must be empty
40039 Reject plate is full
40033 Prerequisites for changing lane width …
40025 Inspection of dispenser nozzle failed
– When the top side of a component is taught, the wizard will be offered instead of the SIPLACE
Vision teaching page.