SIPLACE Station Software 7xx to 714 介绍 - 第46页
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition 46 6.3 Coplanarity Module with 3D Coplanarity Sensor The coplanarity module with the 3D copl anarity sensor (type 37 ) is an optical inspection …
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition
45
6 Feature Description – Station Software V705.x
Features (V705.03)
6.1 DX-Series Placement Machines
The station software supports the new DX1/DX2 and DX4 placement machines. The features of the
705.03 station software version for the DX-series are listed in the sections 6.25 to 6.33.
6.2 PCB Barcode Recognition with PCB Camera
If the barcode is placed on the upper side of the board, it is possible to replace the Traceability
function of the barcode scanner with this function through measurements with the PCB camera.
Due to the travel possibilities of the PCB camera, this function can be used for further use cases as
well. The function has been implemented as follows:
– Barcode reading on boards with the PCB camera for Traceability. The following barcode types
can be read:
1D barcodes: Code 39, Code 93, Code 128, EAN 8, EAN 13
2D barcodes: Data Matrix ECC 200
– Barcode position and size coding in SIPLACE Pro.
– Via multiple measurements, it is possible to read barcodes that are bigger than the field of view
of the PCB camera.
– Teaching of barcodes at the station, data transfer to SIPLACE Pro.
– Definition of filters and the output layout in SIPLACE Vision Editor.
– Reading of barcodes on panels, transfer of the panel barcodes via the Trace service.
– Settings can be made in SIPLACE Pro in order to handle barcodes that cannot be read. If an
error occurs, it is possible to teach again at the station and repeat the measurement.
– Whispering of barcode data through the machine/line. This function requires a license for the
machine from the license server via SIPLACE Pro.
For licensing, this function requires an USB dongle at the machine, item no. [00519852-xx].
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition
46
6.3 Coplanarity Module with 3D Coplanarity Sensor
The coplanarity module with the 3D coplanarity sensor (type 37) is an optical inspection system
and is optionally used as of this station software version on the SIPLACE X2, X3, X4 and SX1/SX2
placement machines as follows:
Placement
machine
Location
Placement
head
Notes
X2, X3
3
Twin Head
X4
2 oder 3
Twin Head
Due to the height layout, only Twin Head/Twin
Head is allowed in this processing area.
SX1, SX2
1
Twin Head
CPP
On the SX2 all allowed heads may be
configured on the neighbor gantry.
The 3D coplanarity sensor has the job of determining the offsets of the connections (leads, balls) of
a component with respect to the placement plane (coplanarity) and the angle to the perpendicular
(colinearity) and compare this with a specified tolerance (solder paste thickness). A valid evaluation
makes a statement as to whether all the measured lead offsets are within the specified tolerances.
The 3D coplanarity sensor projects a laser line. This means, that rapid coplanarity measurements
are also possible for BGAs.
If a SIPLACE Vision Coplan installation has been performed during the installation, the Auto-
configuration offers a coplan sensor that has to be confirmed or rejected during the first start of the
placement machine.
6.3.1 Coplanarity Measurement with the 3D Coplanarity Sensor
Coplanarity measurement with the 3D coplanarity sensor is integrated as of the 705.03 station
software version. Measurement with the 3D coplanarity sensor can be carried out for a number of
component types such as BGAs or components with gull wing leads (without notch). Whether or
not coplanarity measurement should be carried out for each component type is specified in
SIPLACE Pro. The measurement results are displayed in SIPLACE Vision in a way similar to that
for the component measurements. Vision measurement contexts are used for logging erroneous
measurements.
NOTICE
For a detailed description of how to set the recognition parameters for coplanarity
measurement and how to evaluate the measurement results, please refer to the online
help system for SIPLACE Vision.
Station Software 7xx to 714.0 (R20-2) / Feature Description 11/2020 Edition
47
6.4 Support of Long Boards on SX4
On the conveyor type for the SX4 placement machine, boards up to 450 mm length x 560 mm
width are supported. The boards are positioned backwards in the placement section. I.e., a board
is transported into the placement section until the rearmost board edge resides in the placement
section. After that, the stopper is run up in the input section and the board in the placement section
is positioned backwards at the stopper.
6.4.1 Additional Stopper for 380 mm Long Boards
A new stopper is supported for 380 mm long boards. Thus the configuration contains three
stoppers (Standard, Backwards and Stop380). The station accepts at most two stopper positions at
the same time. In a SIPLACE Pro job, either the Backwards or the Stop380 positioning can be
used.
6.5 Alternative Components
Manufacturer-specifically, components of the same type may lightly differ from each other (e.g. in
the geometry, different tape sizes etc.). This means, that the delivered components also differ from
the definition in the placement program. As of this stations software version the placement of such
components is supported. All valid alternative components are defined in SIPLACE Pro. The
selection, which alternative components are to be placed, has to be defined via the forced setup
verification and thus, Setup Center is required for his function. The alternative components to be
placed are displayed on the station software GUI under Feeders, components and nozzles –
Setup – X-feeders / WPC / MTC as follows:
Figure 6-1: Alternative components on WPC (no component selected yet)
The alternative components are marked with a double arrow icon in the upper right corner of the
component name field. By clicking in this field, all possible alternative components are displayed for
the selected pick-up position. In order to select an alternative component for the pick-up position,
the operator has to verify one of the displayed alternatives.
The selected alternative component is displayed in compact display mode and sorted first in
expanded mode:
Figure 6-2: Alternative components at an X-table (444FeederAlti selected)
This function requires a license via SIPLACE Pro. More information on alternative components can
be found in the User Manual for alternative components, item no. [00196839-xx].
Restrictions
The placement of alternative components is only possible in combination with SIPLACE Setup
Center.