Schneller MTC Wechseltisch - 第28页
Assembly instructions Changeover table in place of the MTC2 Special design 03/2007 Edition 28 2.2 Requirement s 2.3 Restrictions It is not possible to use a 3rd tap e reel with 3 x 8mm feeders as there is no suspension p…
Special design Assembly instructions Changeover table in place of the MTC2
03/2007 Edition
27
2 Assembly instructions:
Special design for changeover table
in place of the MTC2, SIPLACE HF
series (SW 505.03, 505.03 SP 1,
505.04)
2.1 Description of the functions
If the changeover table is installed, it can be set up on an HF or HF/3 feeder in place of the MTC2
at location 2 without having to replace the docking unit frame. 2
A JEDEC tray may be placed on the front cover plate. The programming guide for the arbitrary
carrier under SIPLACE Pro (Item no.: 00194607-xx) is provided for this purpose. 2
2
Assembly instructions Changeover table in place of the MTC2 Special design
03/2007 Edition
28
2.2 Requirements
2.3 Restrictions
It is not possible to use a 3rd tape reel with 3 x 8mm feeders as there is no suspension point for
the 3rd reel on the tape reel holder. 2
There is no tape cutter, which means that the component tapes must be cut off beneath the ma-
chine from time to time.
The machine must be stopped first. 2
The table may only be installed at location 2. The necessary changes to the software have not yet
been made for installation at location 4. 2
The special design software must be reinstalled after a software upgrade or a service pack instal-
lation. Please note the requirements. 2
After the installation of the special design "MTC-changeover table" the distributor must not be
started manually from the operating system. 2
No linear feeders can be mounted. 2
2.4 Deliverables
– Changeover table
– 2 screws M8 x 45 mm
– 2 magnets
– CD for software settings
– Sssembly instructions: Special design for changeover table in place of MTC2 (item no.:
00194578-xx)
– Arbitrary carrier programming guide (Item no.: 00194607-xx)
2.5 Tools required
– T-shaped Allen key, size 8
Software
Station software 505.03, 505.03 SP 1 and 505.04
Hardware
HF or HF/3 with MTC 2 at location 2
Special design Assembly instructions Changeover table in place of the MTC2
03/2007 Edition
29
2.6 Safety instructions
WARNING
The safety instructions from the “Operational safety” chapter of the user manual and servicing in-
structions take precedence over these instructions. 2
The SIPLACE placement machines are supplied with mains voltage.
Consequently parts of these systems carry dangerous voltages! This voltage is present at certain
modules inside the machine base, even when the machine is switched off at the main power
switch.
Incorrect handling of the placement machine or touching live parts of the machine can result in
death or severe injury, and considerable damage to equipment.
BEFORE starting any work, shut down the operating system correctly, then switch the machine
OFF at the main power switch and disconnect from the main power supply. In addition, the com-
pressed air supply must be switched off at the compressed air unit's main valve in the machine
base and vented by actuating the needle valve on the compressed air unit.
There is DANGER for heart pacemaker wearers in the vicinity of the linear motors, as described
in detail in the "Special safety instructions for working in the vicinity of strong magnetic fields"
section of the user manual and service manual.
Always follow the accident prevention regulations, DIN or other standards and special safety
rules applicable in your country.
Pay attention to the information concerning residual voltages in the Operational Safety chapter.
Follow the ESD regulations as described in the operational safety section of the operating
instructions.
During the retrofit, always secure the machine to prevent access by other people and to prevent
it being switched on again. The procedure is described in the “Locking the machine…” section of
the user manual.
Working with the SITEST program further increases the risk of accident.
The SITEST program must only be used by authorized and trained personnel.
2
2.6.1 Definitions
2
PLEASE NOTE 2
2