4OM-1011-002 - 第142页
0305-001 Tg0860-PM-MM 3-91 6.8 UNIT MANUAL ALIGNMENT TEACH Display *5 [TEACH ST ART] Key When this key is selected and the [MOVE] button is pressed, the P .E.C. recognition camera moves to the feeder position specified i…
0305-001 Tg0860-PM-MM
6.8.4 Feeder (B) Offset
• After the actually used feeders are installed in each feeder slot No. and
manual alignment operation is performed, the offset values for the feeder
are taught.
When the [FEEDER (B) OFFSET] key is pressed at the “UNIT MANUAL
ALIGNMENT TEACH” display, the following display appears on the screen.
*1 FEEDER #
A feeder slot No. can be set for manual alignment and teaching operations.
Install the feeder to be used in the slot No. specified in the “FEEDER #”
data box.
*2 [ NEXT FDR. #] and [ PREV. FDR. #] Keys
When the [ NEXT FDR. #] key is pressed, the feeder # increases by 1.
When the [ PREV. FDR. #] key is pressed, the feeder # decreases by 1.
*3 [RECOG MARK DATA EDIT] Key
When this key is pressed, the “RECOG. MARK DATA EDIT” display (Fig.
4C168) appears on the screen, enabling the designation of a template shape
to appear on the recognition monitor.
The template shape can be specified for manual alignment with the align-
ment point.
Refer to “6.8.8 Editing of Recognition Mark Data” for details.
*4 [ALL BEAM HEADS ZERO] Key
Both Beams A and B are zeroed.
When this key is selected and the [MOVE] button is pressed, the zeroing
operation starts.
*1
*2
*5
*4
*3
*6
*7
3-90
6.8 UNIT MANUAL ALIGNMENT TEACH Display
Fig. 4C161
0305-001 Tg0860-PM-MM3-91
6.8 UNIT MANUAL ALIGNMENT TEACH Display
*5 [TEACH START] Key
When this key is selected and the [MOVE] button is pressed, the P.E.C.
recognition camera moves to the feeder position specified in the “FEEDER
#” data box.
The pick-up point of the feeder appears on the recognition monitor. Perform
the manual alignment operation, using the track ball.
Refer to “6.8.9 Teaching Operation with Trackball” for details.
*6 OLD DATA
Displayed are the values (the parameters related to the indicated feeder #)
before the feeder (B) offset data is taught.
*7 NEW DATA
Displayed are the values (the parameters related to the indicated feeder #)
after the feeder (B) offset data is taught.
Before the teaching operation is performed, the same values as *6 are dis-
played.
0305-001 Tg0860-PM-MM
6.8.5 Nozzle Stocker Offset
Notes: (a) A special jig (option) is required for accurate teaching operations.
Set the jig to the stocker address position to be taught in advance.
(b) If the offset data is not taught accurately, the nozzle change opera-
tion cannot be performed correctly.
• Set the jig or a nozzle on the nozzle stocker and perform the offset teaching
operation for the feeder through manual alignment operation.
When the [NOZZLE STOCKER OFFSET] key is pressed at the “UNIT
MANUAL ALIGNMENT TEACH” display, the following display appears on
the screen.
[MASTER]
When this key is pressed, the display appears where the nozzle stoker entire
deviation is taught.
[LOCAL]
When this key is pressed, the display appears where the nozzle stokers 1 to
10 are taught individually.
3-92
6.8 UNIT MANUAL ALIGNMENT TEACH Display
Fig. 4C162