4OM-1011-002 - 第154页
0305-001 Tg0860-PM-MM *1 [FEEDER #] Key When this key is pressed, the “PICK-UP LOCA TION TEACH - SET FEEDER” display (Fig. 4C175) appears on the screen, enabling the setting of the feeder No. whose pick-up location must …
0305-001 Tg0860-PM-MM
6.10 PICK-UP LOCATION (TAPE·VIB. STICK) Display
• The offset teaching operation is performed on the pick-up location of the
components to be supplied from the tape and vibratory stick feeders.
When the [TAPE･VIB. STICK] key is pressed at the “PICK-UP LOCA-
TION” display, the following display appears on the screen.
*7
*11
*2
*1
*3
*4
*12
*8 *9
*10
*6
*5
[TEACH ECC. PICKUP POS
[PICKUP LOC. ADJ]] Key
[TEACH PICK-UP POS. [COMP.
CENTER POS.]] Key
3-102
6.10 PICK-UP LOCATION (TAPE·VIB. STICK) Display
Fig. 4C172
Fig. 4C173
0305-001 Tg0860-PM-MM
*1 [FEEDER #] Key
When this key is pressed, the “PICK-UP LOCATION
TEACH - SET FEEDER” display (Fig. 4C175) appears on
the screen, enabling the setting of the feeder No. whose
pick-up location must be taught.
Procedure for Feeder Selection
(1) Select one of the keys A to specify the feeder base.
(2) Select the feeder No., using the [ ] or the [ ] key B.
To teach the data related to the vibratory stick feeder,
select one of the keys C to specify the feeder carriage.
(3) Press the [SET] key.
*2 [ PREV. FEEDER #] and [ NEXT FEEDER #] Keys
The feeder Nos. registered in the component data of the
current program are scrolled up or down.
This function automatically skips the feeder Nos. which are
not specified in the current program or the feeder Nos. for
which no components are set in the component data.
[FDR. -A 101- ]
B
C
[101]
Fig. 4C175
A
Fig. 4C176
3-103
6.10 PICK-UP LOCATION (TAPE·VIB. STICK) Display
Fig. 4C174
Fig. 4C177
0305-001 Tg0860-PM-MM
*3 “SELECT OPTION”
[TEACH PICK-UP POS. [COMP. CENTER POS.]] Key
When this key is pressed, the display (Fig. 4C172) ap-
pears on the screen.
To teach the center position of the component, use this
function for the “FEEDER (B) OFFSET” teaching.
[TEACH ECC. PICKUP POS [PICKUP LOC. ADJ]] Key
When this key is pressed, the display (Fig. 4C173) ap-
pears on the screen.
When a component has a groove, a protrusion, etc., and
cannot be picked up at the center without any hindrance,
use this function for the “PICK-UP LOCATION AD-
JUSTMENT X, Y” teaching.
[COMPONENT DATA (VIB. STICK) OFFSET] Key
When this key is pressed, the display (Fig. 4C195) ap-
pears on the screen.
Use this function to teach “OFFSET X, Y”.
This key can be selected only when the feeder No. se-
lected in *1 is allocated to a vibratory stick feeder.
*4 “MODE: TEACH PICK-UP POSITION”
This is used to additionally modify “FEEDER (B) OFFSET
X, Y”.
[ALL BM. HD. ZERO] Key
Both Beams A and B are zeroed.
When this key is selected and the [MOVE] button is
pressed, the zeroing operation starts.
[CENTER 1-PT.] Key
When this key is selected and the [MOVE] button is
pressed, the P.E.C. recognition camera moves to the com-
ponent center position (Position of “Design Position +
Feeder (A) Offset + Feeder (B) Offset”) of the perti-
nent feeder, making it possible to capture the image.
Under this condition, shift to the trackball operation and
perform the manual alignment operation.
“DIAGONAL 2-PT.” [1POINT] and [2POINT] Keys
These keys are used to align the component with two
diagonally-located points.
Use this function when the maximum outside dimensions
of the component exceed “10 × 10 mm” (when the whole
image of the component cannot be captured on the rec-
ognition monitor).
*5 “MODE: TEACH ECCENTRIC PICK-UP POS.”
6.10 PICK-UP LOCATION (TAPE·VIB. STICK) Display
3-104
Fig. 4C178
Fig. 4C179
Fig. 4C180
“PICK-UP LOCATION ADJUST-
MENT X, Y” in the component li-
brary data is modified additionally.
Incorrect teaching operation will
cause the pick-up rate to deterio-
rate.
CAUTION